Ocean
Controls
PO Box 2191
Seaford BC
Factory 3/24Wise Ave
Seaford,
Vic, Australia 3198
ABN 22 061 932 027
Ph 61 3 9782 5882
Fax 61 3 9782 5517
Email Us
• Catalogue
• Shopping Cart
• Ordering Info
• Specials
• What's
New
• Home
• Audio
• Communications
• Computer
Products
• Controllers
• Counters
Timers
• Data
Acquisition
• Data Loggers
• Micro
Programmers
• Modbus Products
• Moscad RTU
• Motor
Controllers
• Motors
• Panel Meters
• PLC's
• Power Supplies
• Relays
• Sensors
• Signal
Conditioners
• Software Commercial
• Software
Industrial
• Test Equipment
|
Wireless Modules
|
WIR-001 Modem Long Range 433MHz:
UM96 - Includes Antenna and Cable
433MHz Long Range Radio from HAC. These small modems use a seamless
serial interface - whatever enters the TX pin at 9600bps shows up on
the other unit's RX pin. All buffering and error detection is handled
internally. And the best part - with 10mW output, it reaches over 500m!
This unit can be attached to TTL level serial (for microcontrollers) or
directly to RS232 or even RS485 for incredibly simple serial cable
replacement!
Specifications:
* Operating Voltage: 3.3V-5.5V
* 9600bps over 500m
* Modulation type: GFSK
* 8 Channels jumper selectable(4 can be
used in Australia above 433MHz )
* Low power : 30mA RX, 40mA TX, 20uA Sleep
* Small footprint size: 26x47mm
Documents: HAC-UM96 Datasheet
Supported Antennae: Kit comes with 1/4 wave 50Ohm antenna and
communications cable!
|
Download Manual!
Purchase!
|
WIR-002 Modem Long Range 433MHz: UM12 -
Includes Antenna and Cable
433MHz
Long Range Radio from HAC. These small modems use a seamless serial
interface - whatever serial character enters the TX pin at 1200bps
shows up on the other unit's RX pin. All buffering and error detection
is handled internally. And the best part - with 10mW output, it reaches
over 1000m!
This unit can be attached to TTL level serial (for microcontrollers) or
directly to RS232 or even RS485 for incredibly simple serial cable
replacement!
Specifications:
* Operating Voltage: 3.3V-5.5V
* 1200bps over 1000m
* Modulation type: GFSK
* 8 Channels jumper selectable (4 can
be used in Australia above 433MHz )
* Low power : 30mA RX, 40mA TX, 20uA Sleep
* Small footprint size: 26x47mm
Documents: HAC-UM96 Datasheet (Serves both UM96 and UM12)
Supported Antennae: Kit comes with 1/4 wave 50Ohm antenna and
communications cable!
|
Download Manual (Serves both UM96 and UM12)!
Purchase! |
KTA-232 UM96 and UM12 Modem Adapter
The
KT-5232 is an easy to use adapter for the UM96 and UM12 wireless modems.
Just attach the modem, a power supply (8-30VDC) and a serial cable and
you will be up and running in no time.
Use a Male to Female 9-pin serial
Specifications:
* Operating Voltage: 8-30V
* Accepts UM12 and UM96 modems
* D9F Connector
* Jumpers select DCE or DTE modes
|
Download Manual |
WIR-006 Transceiver
MiRF v2 - nRF24L01 Module RP-SMA
The MiRF v2 is the latest in RF modules. This module uses the newest
2.4GHz transceiver from Nordic Semiconductor, the nRF24L01. This
transceiver IC operates in the 2.4GHz band and has many new features!
Take all the coolness of the nRF2401A and add some extra pipelines,
buffers, and an auto-retransmit feature - very nice!
This board features a reverse polarized SMA connector for maximum RF
range. Please remember, you will need a mating RP-SMA 2.4GHz antenna
(listed below).
Comes with 2.4GHz
Duck Antenna 2.2dBi with Reverse Polarized - SMA RF
connector. Perfect for prototyping with our RF ICs. 50 ohm impedance.
4" long.
Features:
* On-board 3.3V LDO Regulator (3.3 to 7V supply allowed)
* Reverse Polarized SMA Connector for external 2.4 GHz Antenna
* 80m Range at 1000kbps
* 2Mbit Data Rate
* Auto Acknowledge
* Auto Re-Trasmit
* Multiceiver - 6 Data Pipes
* 32 Byte seperate TX and RX FIFOs
* 5V tolerant input pins
* Software selectable channel from 2400MHz to 2525MHz (125 Selectable
channels)
* Minimum number of external components
* Pins broken out : VCC, CE, CSN, SCK, MOSI, MISO, IRQ, GND
* Lots of application notes and support on Nordic Semiconductor Website
|
Purchase!
Download
Datasheet
|
WIR-010
Bluetooth Modem
The BlueSMiRF is the latest Bluetooth
wireless serial cable replacement.
These modems work as a serial (RX/TX) pipe. Any serial stream from 9600
to 115200bps can be passed seamlessly from your computer to your
target. We've even tested these units successfully over open air at
350ft (106m)!
The remote unit can be powered from 3.3V up to 6V for easy battery
attachment. All signal pins on the remote unit are 3V-6V tolerant. No
level shifting is required.
The BlueSMiRF
includes hardware flow control (CTS and RTS) and uses a compact ceramic
antenna.
Specifications:
* FCC Approved Class 1 Bluetooth Radio Modem
* Extremely small radio - 0.15x0.6x1.9"
* Very robust link both in integrity and transmission distance (100m) -
no more buffer overruns!
* Low power consumption : 25mA avg
* Hardy frequency hopping scheme - operates in harsh RF environments
like WiFi, 802.11g, and Zigbee
* Encrypted connection
* Frequency: 2.4~2.524 GHz
* Operating Voltage: 3.3V-6V
* Serial communications: 2400-115200bps
* Operating Temperature: -40 ~ +70C
* Built-in antenna
Use a Bluetooth USB Dongle to
communicate between a PC and the modem
|
Purchase! |
Serial
Transmitter Receiver Pair WIR-020 and WIR-021
This transmitter and receiver pair have a usable range up to 30m
Supply Voltage 5VDC
Specifications include:
Transmission Data rate 8KB/sec
Receiver Data rate 4.8KB/Sec
Modulate Mode ASK
Frequency range—433.92MHz
|
Purchase!
Download Manuals
|
Serial
Transmitter Receiver Pair WIR-030
This transmitter and receiver pair is good for data rates up to 4800bps and distance up to 160metres
This wireless data is the easiest to use, lowest cost RF link we have
ever seen! Use these components to transmit position data, temperature
data, even current program register values wirelessly to the receiver.
These modules have up to 500 ft range in open space. The receiver is
operated at 5V and the transmitter operates from 2-12V. The higher the
Voltage, the greater the range - see range test data in the documents
section.
We have used these modules extensively and have been very impressed
with their ease of use and direct interface to an MCU. The theory of
operation is very simple. What the transmitter 'sees' on its data pin
is what the receiver outputs on its data pin. If you can configure the
UART module on a PIC, you have an instant wireless data connection.
Data rates are limited to 4800bps.
The typical range is 500ft for open area.
This is an ASK transmitter module with an output of up to 8mW depending
on power supply voltage. The transmitter is based on SAW resonator and
accepts digital inputs, can operate from 2 to 12 Volts-DC, and makes
building RF enabled products very easy.
This receiver has a sensitivity of 3uV. It operates from 4.5 to 5.5
volts-DC and has digital output. The typical sensitivity is -103dbm and
the typical current consumption is 3.5mA for 5V operation voltage.
Features:
* 315, 418, and 433.92 MHz Operation
pairs
* 500 Ft. Range - Dependant on
Transmitter Power Supply
* 4800 bps transfer rate
* Low cost
* Extremely small and light weight
Documents:
* KLP
Walkthrough Tutorial
* Good
AVR Tutorial
* Receiver
Datasheet
* Transmitter
Datasheet
Supported Antennae: 30-35cm of wire
|
 |
PURCHASING THE WIRELESS MODULES
All prices are in Australian Dollars. Prices do
not include GST (Goods and Services Tax). 10% GST applies to goods
delivered in Australia. Australian GST is not paid on shipments
despatched to an international destination. You can check the exchange
rate by going to http://www.x-rates.com
|
 |
|
|
|
|
|
|
|
|