Features
The UE9-Pro has all the features of the normal
UE9 with the addition of an auxiliary low-speed hi-resolution (24-bit)
sigma-delta ADC. This converter takes about 125 ms per sample and
provides an effective resolution of about 20-bits over the 0-5 or +/-5
volt ranges. Linearity and accuracy are also improved compared to the
normal converter.
- 14 Analog Inputs (12-16 Bits
depending on speed)
- ±5 or 0-5 Volt Maximum
Analog Input Range
- Supports Software or
Hardware Timed Acquisition
- Analog Input Streaming Up To
50 kHz (Ethernet)
- 2 Analog Outputs (12-Bit)
- 23 Digital I/O
- Up to 2 Counters (32-bits
each)
- Up to 6 Timers (Pulse
Timing, PWM Output, Quadrature Input)
- Built-In Screw Terminals for
Some Signals
- USB 2.0/1.1 Full Speed
Interface
- Ethernet 10Base-T Interface
- Dual-Processor Design with
168 MHz of Total Processing Power
- Electrical Isolation
Possible with Ethernet Interface
- Wireless DAQ Possible with
Standard 802.11 Bridges
- No Power Supply Needed for
USB Operation
- Includes Licensed Copy of
DAQFactory Express Software (Win2000+)
- Includes Labview VI's and
software examples
- Includes USB and Ethernet
Cables, Power Supply, and Screwdriver
- Free Firmware Upgrades
- Money Back Guarantee
- Enclosure Size Approximately
3" x 7" x 1"
- Rated for Industrial
Temperature Range (-40 to +85 degrees C)
Analog Inputs
The LabJack
UE9 has 14 external analog inputs (AIN0-AIN13) and 2 internal analog inputs (AIN14-AIN15).
AIN0-AIN3 are available on screw terminals and also on the DB37 connector. All 14 analog
inputs are available on the DB37 connector.
Each analog
input can be configured individually as unipolar (0-5 volts) or bipolar (±5 volts). An
internal PGA provides gains of 1, 2, 4, or 8 (unipolar ranges only at this time). Analog
input resolution is 12-bits at max speed (10 us conversion time), increasing up to 16-bits
at slower speeds (10 ms conversion time).
Analog
inputs can be continuously streamed at up to 50 ksamples/second over Ethernet. USB
streaming is not fully supported at this time. Command/response (software timed) functions
typically take a few milliseconds to execute.
Analog Outputs
The LabJack
UE9 has 2 analog outputs (DAC0 and DAC1) that are available both on screw terminals and
the DB37 connector. Each analog output can be set to a voltage between 0 and about 4.8
volts with 12-bits of resolution.
Digital I/O
The LabJack
UE9 has 23 digital I/O channels which can be individually configured as input,
output-high, or output-low. 8 of these lines are called flexible digital I/O (FIO) and can
be software configured as up to 6 timers and 2 counters.
The first 4
FIO are available on screw terminals and the DB37 connector. All 8 FIO and 3 MIO are
available on the DB37 connector, and 8 EIO and 3 CIO are available on the DB15 connector.
Timers
Up to 6 FIO
can be configured as timers. The timers are very flexible, providing options such as PWM
output, pulse timing, and quadrature input.
Counters
Up to 2 FIO
can be configured as 32-bit counters.
Power Supply
Power can be
provided by the USB cable or an external 5 volt supply (included). When only Ethernet is
connected, and an isolated power supply is used (such as the included wall-wart), the
entire UE9 is electrically isolated.
High Channel Count Applications
By using USB
hubs or Ethernet switches, many LabJacks can be interfaced to a single PC, providing an
inexpensive solution for low-speed high channel count applications.
Wireless Data Acquisition
Combining
the UE9 with a standard 802.11 wireless Ethernet bridge ($50-$200 from any computer
retailer) provides inexpensive wireless data acquisition. Applications include high-speed
continuous wireless data acquisition, long distance remote sensing and control, or PDA
based data acquisition.
Satisfaction Guaranteed
Everything
we sell has a 30-day money back guarantee. If, for any reason, you are not satisfied with
a product, contact us to arrange your choice of a refund or replacement. In addition, the
LabJack UE9 is covered by a 1-year limited warranty.
Technical Support
All LabJacks
include lifetime technical support. Support resources include
forum and
FAQs.
Optional Accessories
The LabJack UE9 comes complete, but
we do offer a few optional accessories.
| CB37 Terminal Block
-- Provides convenient screw terminals for the DB37 connector on the LabJack UE9. The CB37
can connect directly to the UE9 or can be attached with the included cable.
|
 |
| CB15 Terminal Block
-- Provides convenient screw terminals for the DB15 connector on the LabJack UE9. The CB15
can connect directly to the UE9 or can be attached with the included cable. |
 |
EB37 Experiment
Board -- The EB37 experiment board connects to the LabJack UE9’s DB37
connector and provides convenient screw terminal access. Also provided is a solderless
breadboard
and useful power supplies (+/-10 volts, 3.3 volts, and 1.25 volts). Includes a
screwdriver, power supply, and jumper wires. For the LabJack UE9 only. |
 |
Dual
Amplifier or Voltage Divider Module
Our dual amplifier or voltage divider
module allows you to amplify signals by a factor of 1.5 to x10 or
reduce signals by
a
factor 0.667 to 0.1
You can easily convert 4 to 20mA signals to
voltage.
For more information |
 |
Dual
Programmable Instrumentation Amplifier
A dual instrumentation amplifier from Electronic
Innovations Corp provides 2 high-impedance differential inputs. Operates from a single
5 volt supply and provides a +/- 15 volt supply and a 4.096 volt reference. Analog input
range is +/- 10 volts. The gain of each channel is set to 1, 10, 100, or 1000 via digital
I/O or jumper wires. Typical current requirement is about 80 mA @ 5 volts, allowing the
EI-1040 to be powered from a +5V terminal on the LabJack U12. Download the EI-1040 PDF datasheet
|
 |
LJTick-Divider
The LJTick-Divider (LJTD) is a signal-conditioning module designed
to divide 2 single-ended channels of 0-10 volt analog signals down
to 0-2.5 volt signals. The 4-pin design plugs into the standard
AIN/AIN/GND/VS screw terminal block found on newer LabJacks such as
the U3 and UE9. The use of large resistors and a precision op-amp
buffer provide an input impedance of 1 MW. By adding or replacing
resistors, many other configurations are possible, such as a level
shifter that converts ±10 volts to 0-2.5 volts.
|
 |
LJTick-Current Shunt
The LJTick-CurrentShunt (LJTCS) is a signal-conditioning module
designed to convert a 4-20 mA current loop input signal into a
0.47-2.36 volt signal compatible with the LabJack U3 or UE9. The
4-pin design plugs into the standard AIN/AIN/GND/VS screw terminal
block found on newer LabJacks such as the U3 and UE9.
(RoHS=YES). |
 |
LJTick-InAmp
Signal-conditioning module provides two instrumentation amplifiers
ideal for low-level signals such as bridge circuits (e.g. strain
gauges) and thermocouples. The LJTIA has switches to choose from 5
gain settings (x1, x11, x51, x201, or custom) and two output voltage
offsets. The 4-pin design plugs into the standard AIN/AIN/GND/VS
screw terminal block found on newer LabJacks such as the U3 and UE9.
(RoHS=YES).
|
 |
LJTick-RelayDriver
The LJTick-RelayDriver (LJTRD) allows 2 digital I/O lines on a U3 or
UE9 to control a relay or other moderate load up to 50V/200mA.
|
 |
LJTick-Proto
The LJTick-Proto (LJTP) consists of an 8x8 grid of holes for
prototyping custom signal-conditioning ticks for the LabJack U3 or
UE9.
|
 |
Temperature
Probe
An inexpensive and easy to use temperature probe. Designed to work with a LabJack, but can
also be used with any voltage measuring device. Outputs 10 mV per degree C, and has a
range of -40 to +100 degrees C. Download the EI-1022 PDF datasheet
|
 |
Stainless Steel Temperature
Probe
An easy to use, very accurate, and waterproof
temperature probe from Electronic Innovations Corp.
The sensor is mounted in a stainless steel sheath and features a
high-level linear output of 10 mV per degree F, typical accuracy of
+/-0.25 degrees
C (
+/-0.4 degrees F) at room temperature, and a range of 0 to +300
degrees F (-17 to +150 degrees C, with U3/UE9)
Download the EI-1034 PDF datasheet |
 |
Using
Thermocouples, RTD, mV sources or Potentiometers with Labjack
We sell a range of programmable transmitters
which will convert the output of any thermcouple, RTD, mV source or potentiometer to a
4-20mA signal or 0-10V signal.
Purchasing
All prices are in Australian Dollars.
Prices do not include GST (Goods and Services Tax). 10% GST applies to goods delivered in
Australia. Australian GST is not paid on shipments despatched to an international
destination. You can check the exchange rate by going to http://www.x-rates.com
|
