Features
- 4 Analog Inputs (10 Bits
0-5V)
- 16 Digital Inputs
- 16 Digital Outputs ( Open Collector )
- Serial Port with
Programmable Baud Rate
-
DLL is
Provided
- Screw Terminals for Signals
and Power Supply
- Watchdog mode: can be used
to monitor network connections.
- Ethernet 10Base-T Interface
- 10 MIPS ethernet interface.
- Will work on local or wide
area connections (Internet)
- Automatic detection of IP
address (DHCP).
- Responds to Pings.
Description of Board
Netiom-UDP is a
stand-alone network aware Input / Output module which can be controlled over most
ethernet networks.
It has 16 digital and 4 analogue inputs, 16 digital outputs and an RS232 serial port, all
of which can be accessed from your visual basic or c
program using our DLL component.
Special interface software is included which can be use to configure Netiom and download
web pages via a PCs serial port. Network settings can be manually set or automatically
obtained from a DHCP server (usually an ADSL router).
Specifications
- Power 12V d.c. at 50mA
- Serial Port Programmable baud rate 2400 to 38400 baud (Handshaking not supported).
- Ethernet 10 MIPS via RJ45 connector
- Outputs (16) Open collector 50V d.c. at 50mA
- Digital Inputs (16) TTL / CMOS / dry contacts (10K ohm pull up).
- Analogue Input (4) 10 bit resolution with 0.5% accuracy. Max voltage 5Volts.
Connections
- Digital Inputs - Screw terminal or 10 way header.
- Outputs - Screw terminal or 10 way header.
- Analogue Input - Screw terminal
- Power Screw terminal
- Serial - 9 pin D connector
- Ethernet- RJ45
Software
PC based software is provided to configure the card.
A DLL is also provided to allow you to write your own supervisory and
control programs in C and VB
Download the manuals
Download the DLL manual and VB Program Example
Satisfaction GuaranteedEverything we sell has a 30-day money back guarantee. If, for any
reason, you are not satisfied with a product, contact us to arrange your choice of a
refund or replacement. In addition, the Net-Iom is covered by a 1-year limited
warranty.
Technical Support
Includes
lifetime technical support.
| Relay
Expansion Module -- The Relay Expansion Module connects directly to the NETIOM module.
It has 8 single pole change over relays each rated at 1 amp d.c. at 24 Volts d.c. /110
Volts a.c. Connection to the module is via a 10 way ribbon connector (provided) which
carries the eight output lines plus power.
|
 |
The Optoisolation Module - connects directly to our range of
VIOM and NETIOM products. It has 8 optoisolators for systems which require a high level of
isolation and noise immunity. Two versions are available, one with a common optoisolator
supply rail the other with each optoisolator’s supply separate. Connection to the
module is via a 10 way ribbon connector (provided) which carries the eight output lines
plus power |
 |
The Led Display Board - The LED Display Module connects
directly to our range of VIOM and NETIOM products. It has 8 x 3mm red LEDs. Connection to
the module is via a 10 way ribbon connector (provided) which carries the eight output
lines plus power. As well as display functions the module is also very useful as an
installation / diagnostic aid.
|
 |
| An
inexpensive and easy to use temperature probe. Designed to work with a LabJack, but can
also be used with any voltage measuring device. Outputs 10 mV per degree C, and has a
range of -40 to +100 degrees C.
Download the EI-1022 PDF datasheet
|
 |
Purchasing
All prices are in Australian Dollars.
Prices do not include GST (Goods and Services Tax). 10% GST applies to goods delivered in
Australia. Australian GST is not paid on shipments despatched to an international
destination. You can check the exchange rate by going to http://www.x-rates.com
|
