Features
- 16 Digital Inputs
- 16 Digital Outputs ( Open Collector )
- Serial Port with
Programmable Baud Rate
- Ethernet 10Base-T Interface
- 10 MIPS ethernet interface.
- Will work on local or wide
area connections (Internet)
- Automatic detection of IP
address (DHCP).
- Responds to Pings.
Description of Operation
Netiom-Link
works as a pair of devices communicating over an ethernet network. Each Netiom-Link
transmits a packet of data to its opposite end containing information about its input
status. Upon receipt of this data the receiving device changes its outputs to reflect the
new message data.
In this way all 16 inputs on one Netiom –Link are reflected on the outputs of the
second Netiom-Link. In a similar way serial data coming into one port will be transmitted
out of the serial port of the second Netiom-Link.
Messages between the two modules is sent periodically at a user defined rate. If a change
in the input conditions is detected or a new serial data stream is arrives then this
period is over-ridden and a new message is sent immediately. In this way network traffic
is kept to a minimum while response time is maximised.
One of the outputs can be programmed to show the current status of the link.
Netiom-Link will work over both local and wide area networks such as the internet.
Special interface software is included which can be use to configure Netiom and download
web pages via a PCs serial port. Network settings can be manually set or automatically
obtained from a DHCP server (usually an ADSL router).
Specifications
- Power 12V d.c. at 50mA
- Serial Port Programmable baud rate 2400 to 38400 baud (Handshaking not supported).
- Ethernet 10 MIPS via RJ45 connector
- Outputs (16) Open collector 50V d.c. at 50mA
- Digital Inputs (16) TTL / CMOS / dry contacts (10K ohm pull up).
- Size 110 x 110mm
Connections
- Digital Inputs - Screw terminal or 10 way header.
- Outputs - Screw terminal or 10 way header.
- Analogue Input - Screw terminal
- Power Screw terminal
- Serial - 9 pin D connector
- Ethernet- RJ45
Satisfaction
Guaranteed
Everything we sell has a 30-day money back guarantee. If, for any
reason, you are not satisfied with a product, contact us to arrange your choice of a
refund or replacement. In addition, the Net-Iom is covered by a 1-year limited
warranty.
Technical Support
Includes
lifetime technical support.
| Relay
Expansion Module -- The Relay Expansion Module connects directly to the NETIOM module.
It has 8 single pole change over relays each rated at 1 amp d.c. at 24 Volts d.c. /110
Volts a.c. Connection to the module is via a 10 way ribbon connector (provided) which
carries the eight output lines plus power.
|
 |
The Optoisolation Module - connects directly to our range of
VIOM and NETIOM products. It has 8 optoisolators for systems which require a high level of
isolation and noise immunity. Two versions are available, one with a common optoisolator
supply rail the other with each optoisolator’s supply separate. Connection to the
module is via a 10 way ribbon connector (provided) which carries the eight output lines
plus power |
 |
The Led Display Board - The LED Display Module connects
directly to our range of VIOM and NETIOM products. It has 8 x 3mm red LEDs. Connection to
the module is via a 10 way ribbon connector (provided) which carries the eight output
lines plus power. As well as display functions the module is also very useful as an
installation / diagnostic aid.
|
 |
Purchasing
All prices are in Australian Dollars.
Prices do not include GST (Goods and Services Tax). 10% GST applies to goods delivered in
Australia. Australian GST is not paid on shipments despatched to an international
destination. You can check the exchange rate by going to http://www.x-rates.com
|
