Ocean Controls

LSK-002 PC Serial Tuning Cable for MicroStepper and Servo Drives

Thu, 17 May 2012 14:27:56 +1000

PC Serial Tuning Cable for MicroStepper Drives. Used with ProTuner software to tune the following stepper and servo motor drives

SMC-010 DM422 Anti-Resonance Stepper Motor Drive

Price: $2.50

LSK-001 PC Serial Tuning Cable for MicroStepper Drives

Thu, 17 May 2012 13:57:05 +1000

PC Serial Tuning Cable for MicroStepper Drives. Used with ProTuner software to tune the following stepper and servo motor drives

SMC-007 DM556 Anti-Resonance Stepper Motor Drive
SMC-008 DM432 Anti-Resonance Stepper Motor Drive
SMC-009 DM856 Anti-Resonance Stepper Motor Drive
SMC-011 AM882 Anti-Resonance Stepper Motor Drive
SMC-012 DM442 Anti-Resonance Stepper Motor Drive
SMC-242 DCS-810 Servo Motor Drive
SMC-400 ACS-606 Brushless Servo Motor Drive
SMC-410 ACS-806 Brushless Servo Motor Drive

Price: $2.50

POL-1497 RoboClaw DC Motor Driver 2 x 30A

Thu, 17 May 2012 11:11:51 +1000

The RoboClaw from Basic Micro is an extremely efficient, versatile, dual channel synchronous regenerative motor controller. It supports dual quadrature encoders and can supply two brushed DC motors with 30 A continuous and twice as much peak, at voltages from 6 to 30 V.

The RoboClaw features dual quadrature decoding capability. A built-in PID routine can be used for closed-loop speed control, maintaining motor speeds even if the load varies, or the encoder counts and speeds can be read directly from the RoboClaw for use with an external control system.

Several interface modes are supported by the RoboClaw. It can be controlled via TTL serial for use with an embedded system or a PC with a serial adapter, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), or analog voltages for use with potentiometers or analog joysticks.

Features:

Simple bidirectional control of two brushed DC motors
6 V to 30 V operating supply range
30 A continuous current output, to 60 A peak
        Three communication or control options:
    - Logic-level (TTL) serial interface for direct connection to microcontrollers or other embedded controllers, or connection to a PC with a serial port (external RS-232 level converter required) or USB-to-serial adapter
    - Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    - 05 V analog voltage interface for direct connection to potentiometers and analog joysticks
Dual quadrature encoder inputs up to 8,000,000 encoder pulses per second
(Open-loop control with no feedback also available.)
Screw terminals for quick connect/disconnect
Configurable via onboard DIP switches
Regenerative braking
Tolerates high-speed direction changes
Jumper-selectable 5 V BEC
Battery monitoring and under-voltage cutoff protects batteries from over-discharging

Dimensions: 7.7 x 6.6 x 2.5cm
.

Price: $134.95

AXS-151 Pressure Transmitter 0 to 5 Bar

Thu, 17 May 2012 10:28:48 +1000

These are a great economical gauge pressure transmitter with a 4 to 20 mA output (2 wire) and featuring an accuracy of 0.5% Full Scale. The sensor mounts with a " NPT thread.

Features:

Accuracy: 0.5 % F.S.
Thick film strain guage on ceramic and stainless steel (SUS316)
0 to 5 bar Measurement range
Response time <5mSecs
Supply range 10 to 30 V_DC
16 bit resolution DAC, 4 to 20mA output
" NPT thread
Protection class NEMA4/IP65
CE EMC certification

Specifications:

Power Supply:	10 to 30 V_DC
Measuring Accuracy:	0.5% Full scale
Maximum Pressure:	12 bar
Burst Pressure:	18 bar
Response Time (0 to 90 %):	5 ms
Output Drive Capability:	≤((V_S-10)/0.02) Ω
Output Ripple:	<0.1% Full scale
Connector:	DIN mini connector 43650-A
Connector Protection:	IP65
Output Ripple:	<0.1%FS
Diaphragm Material:	Ceramic Al₂O₃ - 96%
Pressure Port Material:	Stainless steel 1.4401(SUS316)
Operating Temperature Range:	-25 to 85 C
Storage and Medium Range:	-40 to 125 C
Dimensions:	25 mm Dia 86 mm High
Manufacturer Part:	SP-G5001-A2

Documents:

We carry a selection of the full range of options listed in the datasheet. Non-stocked configurations may be available but may be subject to minimum order quantities or different pricing. Contact us for more information

Download Datasheet

Pressure Sensor Comparison

Price: $149.00

AXS-148 Pressure Transmitter -1 to 0 Bar

Thu, 17 May 2012 10:10:11 +1000

These are a great economical gauge pressure transmitter with a 4 to 20 mA output (2 wire) and featuring an accuracy of 0.5% Full Scale. The sensor mounts with a " NPT thread.

Features:

Accuracy: 0.5 % F.S.
Thick film strain guage on ceramic and stainless steel (SUS316)
-1 to 0 bar Measurement range
Response time <5mSecs
Supply range 10 to 30 V_DC
16 bit resolution DAC, 4 to 20mA output
" NPT thread
Protection class NEMA4/IP65
CE EMC certification

Specifications:

Power Supply:	10 to 30 V_DC
Measuring Accuracy:	0.5% Full scale
Maximum Pressure:	4 bar
Burst Pressure:	6 bar
Response Time (0 to 90 %):	5 ms
Output Drive Capability:	≤((V_S-10)/0.02) Ω
Output Ripple:	<0.1% Full scale
Connector:	DIN mini connector 43650-A
Connector Protection:	IP65
Output Ripple:	<0.1%FS
Diaphragm Material:	Ceramic Al₂O₃ - 96%
Pressure Port Material:	Stainless steel 1.4401(SUS316)
Operating Temperature Range:	-25 to 85 C
Storage and Medium Range:	-40 to 125 C
Dimensions:	25 mm Dia 86 mm High
Manufacturer Part:	SP-Gx102-A2

Documents:

Download Datasheet

Pressure Sensor Comparison

Price: $149.00

AXS-149 Pressure Transmitter -1 to 2 Bar

Thu, 17 May 2012 10:06:10 +1000

These are a great economical gauge pressure transmitter with a 4 to 20 mA output (2 wire) and featuring an accuracy of 0.5% Full Scale. The sensor mounts with a " NPT thread.

Features:

Accuracy: 0.5 % F.S.
Thick film strain guage on ceramic and stainless steel (SUS316)
-1 to 2 bar Measurement range
Response time <5mSecs
Supply range 10 to 30 V_DC
16 bit resolution DAC, 4 to 20mA output
" NPT thread
Protection class NEMA4/IP65
CE EMC certification

Specifications:

Power Supply:	10 to 30 V_DC
Measuring Accuracy:	0.5% Full scale
Maximum Pressure:	4 bar
Burst Pressure:	6 bar
Response Time (0 to 90 %):	5 ms
Output Drive Capability:	≤((V_S-10)/0.02) Ω
Output Ripple:	<0.1% Full scale
Connector:	DIN mini connector 43650-A
Connector Protection:	IP65
Output Ripple:	<0.1%FS
Diaphragm Material:	Ceramic Al₂O₃ - 96%
Pressure Port Material:	Stainless steel 1.4401(SUS316)
Operating Temperature Range:	-25 to 85 C
Storage and Medium Range:	-40 to 125 C
Dimensions:	25 mm Dia 86 mm High
Manufacturer Part:	SP-Gx302-A2

Documents:

Download Datasheet

Pressure Sensor Comparison

Price: $149.00

POL-1496 RoboClaw DC Motor Driver 2 x 15A

Tue, 15 May 2012 16:43:26 +1000

The RoboClaw from Basic Micro is an extremely efficient, versatile, dual channel synchronous regenerative motor controller. It supports dual quadrature encoders and can supply two brushed DC motors with 15 A continuous and twice as much peak, at voltages from 6 to 30 V.

Features:

Simple bidirectional control of two brushed DC motors
6 V to 30 V operating supply range
15 A continuous current output, to 30 A peak
        Three communication or control options:
    - Logic-level (TTL) serial interface for direct connection to microcontrollers or other embedded controllers, or connection to a PC with a serial port (external RS-232 level converter required) or USB-to-serial adapter
    - Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    - 05 V analog voltage interface for direct connection to potentiometers and analog joysticks
Dual quadrature encoder inputs up to 8,000,000 encoder pulses per second
(Open-loop control with no feedback also available.)
Screw terminals for quick connect/disconnect
Configurable via onboard DIP switches
Regenerative braking
Tolerates high-speed direction changes
Jumper-selectable 5 V BEC
Battery monitoring and under-voltage cutoff protects batteries from over-discharging

Dimensions: 7.7 x 6.6 x 2.5cm
.

Price: $99.95

ATO-115 SE5404D 4 Port RS-232/RS-422/RS-485 10/100 Mb Ethernet Serial Server

Tue, 15 May 2012 15:23:20 +1000

The Industrial Serial Server SE5404D is a cost effective 4 port gateway for Ethernet (TCP/IP) and serial signal communications. It allows almost any serial device to be connected to a new or existing Ethernet network.

By encapsulating serial data and transporting it over Ethernet, SE5404D offers full-duplex and bi-directional data that is transmission transparent between the serial port and the Ethernet network.

Flexible configuration options enable this unit to be setup over Ethernet by Telnet, Web browser, Serial Console, or a downloadable Windows utility. Packed in a rugged metal housing for wall or DIN-Rail mount with 9 VDC or 9 to 48 VDC wide power input range, SE5404 is ideal for almost any industrial and manufacturing automation.

ATOP Virtual COM software provides existing Windows based application to access serial device by mapping the Virtual COM port to a remote serial server via Ethenet. Windows software works with XP, Vista and 7. TTYredirector software is downloadable from ATOP for 32 bit and 64 bit, x86 Linux.

In industrial and manufacturing automation fields, SE5002 is used as a field device to connect the Ethernet through TCP/IP protocol directly. It is also specially designed for conjunction with PLCs, HMIs, Barcode Scanners, Data Terminals, Electronic Kanbans, Shop Floor Control Systems, and Pick-to-Light Systems.

Specifications:

Ethernet
Compliance:	IEEE802.3
Transmission Rate:	10/100Mbps Auto-detection
Connector:	RJ-45
Auto MDI/MDI-X:	Yes

Link Mode
TCP Server:	up to 4 connections or Virtual Com mode
TCP Client:	up to 2 destination or Virtual Com mode
UDP:	Up to 8 Ranges of IPs

Serial
Interface:	RS-232/422/485 software selectable
Ports:	4 independent serial ports
Baud Rate:	300 bps to 921 kbps
Parity:	None, Odd, Even, Mark, Space
Data Bits:	7, 8
Stop Bits:	1, 2
Flow Control:	None, Software: Xon/Xoff, Hardware: RTS/CTS
Protection:	15 kV ESD
Connector:	7 pin, 5.08 mm connector for redundant terminal block

Power
Input:	9 to 48 VDC
Consumption:	≤1.5 W

Approval
EMC:	FCC Class A, CE Class A

Environment
Operating	-40 to 80 C (-40 to 176 F)
Storage:	-40 to 85 C (-40 to 185 F), 5 to 95% RH

Dimension
W H D:	54 146 120 mm

Software
Configuration:	Web Page / Telnet / Serial console / Windows utility
Virtual Com:	Windows and Linux port redirection software
Support Protocol:	ICMP, TCP(UDP) / IP, DHCP client, SNMP, HTTP

Documents:

Download datasheet
Software and Manuals on ATOP's website

Price: $479.00

SFK-003 Car Diagnostics Kit

Mon, 14 May 2012 15:02:21 +1000

This board allows you to interface with your car's OBD-II bus. It provides you a serial interface using the ELM327 command set and supports all major OBD-II standards such as CAN and JBUS. The board also provides a footprint which mates directly to our FTDI Basic or a Bluetooth Mate. The DB9 connector mates with our DB9 to OBD-II cable listed below.

On-Board Diagnostics, Second Generation (OBD-II) is a set of standards for implementing a computer based system to control emissions from vehicles. It was first introduced in the United States in 1994, and became a requirement on all 1996 and newer US vehicles. Other countries, including Canada, parts of the European Union, Japan, Australia, and Brazil adopted similar legislation. A large portion of the modern vehicle fleet supports OBD-II or one of its regional flavors.

Among other things, OBD-II requires that each compliant vehicle be equipped with a standard diagnostic connector (DLC) and describes a standard way of communicating with the vehicles computer, also known as the ECU (Electronic Control Unit). A wealth of information can be obtained by tapping into the OBD bus, including the status of the malfunction indicator light (MIL), diagnostic trouble codes (DTCs), inspection and maintenance (I/M) information, freeze frames, VIN, hundreds of real-time parameters, and more.

STN1110 is an OBD to UART interpreter that can be used to convert messages between any of the OBD-II protocols currently in use, and UART. It is fully compatible with the de facto industry standard ELM327 command set. Based on a 16-bit processor core, the STN1110 offers more features and better performance than any other ELM327 compatible IC.

Features:

Fully compatible with the ELM327 AT command set
Extended ST command set
UART interface (baud rates from 38 bps to 10 Mbps)
Secure bootloader for easy firmware updates
Support for all legislated OBD II protocols:
- ISO 15765-4 (CAN)
- ISO 14230-4 (Keyword Protocol 2000)
- ISO 9141-2 (Asian, European, Chrysler vehicles)
- SAE J1850 VPW (GM vehicles)
- SAE J1850 PWM (Ford vehicles)
Support for non-legislated OBD protocols:
- ISO 15765
- ISO 11898 (raw CAN)
Support for SAE J1939 OBD protocol
Superior automatic protocol detection algorithm
Large memory buffer
Voltage input for battery monitoring

Kit Includes:

OBD-II UART Board
OBDII to DB9 Cable

Documents:

Schematic
Eagle Files
SparkFun's Quickstart Guide
Datasheet (STN1110)
Datasheet (MCP2551)
ELM327 Command Set
Compatible Software List
SparkFun Product Video that includes the Kit

Price: $59.00

KTB-272 Two 24VDC 20A Relay Card

Thu, 10 May 2012 08:34:35 +1000

This relay card features 2 JQX-15F(T90) relays. Please note the card has been designed to switch DC voltages up to 48VDC (It is not designed to switch 110 or 240VAC loads). The card includes a relay driver allowing a very wide range of input configurations. The driver allows direct connection to many logic families, industrial sensors (NPN or PNP) dry contacts or voltage outputs.

Each relay has HI and LO input terminals. The relay is activated when the HI terminal is driven high or the LO terminal is driven to a low voltage. Each channel has an indicator LED.

A 3.5 mm hole in each corner allows easy mounting on a panel.

A 3 position switch can be used with the card to provide a 20A DC motor controller with forward-off-reverse control. LEDs L3 and L4 provide indication showing direction of movement (see manual for further information).

Please note that wiring high voltage can be dangerous and if at all unsure, you should contact an electrician to ensure your installation is safe and meets relevant specifications.

Specifications:

Supply Voltage:	11.3 to 13.2 VDC
Supply Current:	~2 ma/channel + ~80 mA/active relay
Low Input Activation Voltage:	≤0.8 VDC
Low Input Voltage Range:	0 V to Supply Voltage
High Input Activation Voltage:	≥2.4 VDC
High Input Voltage Range:	0 V to Supply Voltage
Output Form:	1-Z SPDT (NO & NC)
Output Switch Voltage:	28 VDC
Output Load Current:	20 A (28 VDC)
Relay Coil to Contact Isolation:	≥1,500 VAC
Relay Contact to Contact Isolation:	≥1500 VAC
Relay Contact Resistance:	≤100 mΩ
Dimensions:	78 72 23 mm

Other Versions:

This card is also available in a DIN-rail mount version,

Documents:

Download Datasheet

Price: $49.00

NOI-006 N320 Temperature Indicator (PT100 RTD) 24VDC

Thu, 10 May 2012 08:31:31 +1000

The N320 is a panel-mount temperature indicator offering 3 highly visible LED digits. The temperature indicator has configurable offset correction capability and hysteresis. Suits PT100 RTD sensors.

Features:

3 digit LED display
Sensor offset adjustment
Adjustable hysteresis
Configuration preserved through power failures
Configurable password for configuration lock
Long life silicone keys
CE and UL Certified. (USA and Canada)
IP65 when installed into a panel

Specifications:

Range of Measurement:	-50 to 300 C (-58 to 572 F)
Accuracy:	0.7 C (1.26 F)
Resolution:	0.1 C or 0.1 F ranging from -19.9 to 199.9 C/F
Sample Rate:	1.5 Hz
Power Supply:	12 to 24 VDC 10%
Power Consumption:	5 VA
Dimensions:	75 33 75 mm
Panel Cutout:	70 29 mm
Weight:	120 g
Operating Temperature:	0 to 40 C (32 to 104 F)
Storage Temperature:	-20 to 60 C (-4 to 140 F)
Manufacturer Part:	N320 PT100

Documents:

Download the flier

Download the manual for full product details

Price: $79.00

NOI-004 N320 Temperature Indicator (JKT Thermocouple) 24VDC

Thu, 10 May 2012 08:29:55 +1000

The N320 is a panel-mount temperature indicator offering 3 highly visible LED digits. The temperature indicator has configurable offset correction capability and hysteresis. Suits J, K or T type thermocouples.

Features:

3 digit LED display
Sensor offset adjustment
Adjustable hysteresis
Configuration preserved through power failures
Configurable password for configuration lock
Long life silicone keys
CE and UL Certified. (USA and Canada)
IP65 when installed into a panel

Specifications:

Range of Measurement:	J: 0 to 600 C (32 to 1112 F) K: -50 to 1000 C (-58 to 1832 F) T: -50 to 400 C (-58 to 752 F)
Accuracy:	3 C (5.4 F)
Resolution:	0.1 C or 0.1 F ranging from -19.9 to 199.9 C/F
Sample Rate:	1.5 Hz
Power Supply:	12 to 24 VDC 10%
Power Consumption:	5 VA
Dimensions:	75 33 75 mm
Panel Cutout:	70 29 mm
Weight:	120 g
Operating Temperature:	0 to 40 C (32 to 104 F)
Storage Temperature:	-20 to 60 C (-4 to 140 F)
Manufacturer Part:	N320 JKT

Documents:

Download the flier

Download the manual for full product details

Price: $89.00

NOI-002 N320 Temperature Indicator (NTC Thermistor) 24VDC

Thu, 10 May 2012 08:25:31 +1000

The N320 is a panel-mount temperature indicator offering 3 highly visible LED digits. The temperature indicator is supplied with a NTC Thermistor 3 m cable and with offset correction capability.

Features:

3 digit LED display
Sensor offset adjustment
Includes NTC thermistor sensor with 3 m cable
Adjustable hysteresis
Configuration preserved through power failures
Configurable password for configuration lock
Long life silicone keys
CE and UL Certified. (USA and Canada)
IP65 when installed into a panel

Specifications:

Range of Measurement:	-50 to 120 C (-58 to 248 F)
Accuracy:	0.6 C (1.08 F)
Resolution:	0.1 C or 0.1 F ranging from -19.9 to 199.9 C/F
Sample Rate:	1.5 Hz
Power Supply:	12 to 24 VDC 10%
Power Consumption:	5 VA
Dimensions:	75 33 75 mm
Panel Cutout:	70 29 mm
Weight:	120 g
Operating Temperature:	0 to 40 C (32 to 104 F)
Storage Temperature:	-20 to 60 C (-4 to 140 F)
Manufacturer Part:	N320 NTC

Documents:

Download the flier

Download the manual for full product details

Price: $79.00

KTA-272 Two 12VDC 20A Relay Card

Wed, 09 May 2012 11:25:41 +1000

This relay card features 2 JQX-15F(T90) relays. Please note the card has been designed to switch DC voltages up to 48 VDC (It is not designed to switch 110 or 240 VAC loads). The card includes a relay driver allowing a very wide range of input configurations. The driver allows direct connection to many logic families, industrial sensors (NPN or PNP) dry contacts or voltage outputs.

Each relay has HI and LO input terminals. The relay is activated when the HI terminal is driven high or the LO terminal is driven to a low voltage. Each channel has an indicator LED.

A 3.5 mm hole in each corner allows easy mounting on a panel.

A 3 position switch can be used with the card to provide a 20 ADC motor controller with forward-off-reverse control. LEDs L3 and L4 provide indication showing direction of movement (see manual for further information).

Please note that wiring high voltage can be dangerous and if at all unsure, you should contact an electrician to ensure your installation is safe and meets relevant specifications.

Specifications:

Supply Voltage:	11.1 to 13.2 VDC
Supply Current:	~2 ma/channel + ~80 mA/active relay
Low Input Activation Voltage:	≤0.8 VDC
Low Input Voltage Range:	0 V to Supply Voltage
High Input Activation Voltage:	≥2.4 VDC
High Input Voltage Range:	0 V to Supply Voltage
Output Form:	1-Z SPDT (NO & NC)
Output Switch Voltage:	240 VAC, 28 VDC
Output Load Current:	20 A (240 VAC), 20 A (28 VDC)
Relay Coil to Contact Isolation:	≥1,500 VAC (1 minute)
Relay Contact to Contact Isolation:	≥750 VAC (1 minute)
Relay Contact Resistance:	≤100 mΩ
Dimensions:	78 72 23 mm

Other Versions:

This card is also available in a DIN-rail mount version.

Documents:

Download Datasheet

Price: $49.00

KTA-274 Loop Powered Ambient Light Sensor

Fri, 04 May 2012 16:47:50 +1000

The KTA-274 is a 4-20mA loop powered ambient light sensor with human eye response, outputting 4 mA for 0 lux and 20 mA for 1000 lux, based on the TEMT6000 ambient light sensor from Vishay Semiconductors.
The KTA-274 is housed in a clear top IP65 enclosure with PG7 cable gland for cable entry.

Features:

Loop Powered
4-20mA Injector
Screw Terminal Connections
40V Maximum Loop Voltage
IP65 Wall Mount Enclosure

Download Manual

Price: $99.00

SFS-406 Flexiforce Pressure Sensor - 25lbs (1" area)

Tue, 01 May 2012 11:06:33 +1000

This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~50k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when pressure is applied to the round area at the end of the sensor. Used as a presence sensor (someone standing), weight sensor, pressure sensor (impact testing), etc.

The overall length is about 2.25". The sensor comes with a 0.1" spaced, reinforced, breadboard friendly connector.

This sensor ranges from 0 to 25lbs of pressure.

Documents:

Price: $25.00

SFS-405 Force Sensitive Resistor - Small

Tue, 01 May 2012 10:58:54 +1000

This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR, its resistance will be larger than 1MΩ, with full pressure applied the resistance will be 2.5kΩ.

Two pins extend from the bottom of the sensor with 0.1" pitch making it bread board friendly.

These sensors are simple to set up and great for sensing pressure, but they aren't incredibly accurate. Use them to sense if it's being squeezed, but you may not want to use it as a scale.

Dimensions:

Overall length: 44.5 mm
Overall width: 6.4 mm
Sensing area: 7.6 mm

Documents:

FSR Integration Guide

Price: $6.00

SMC-204 PC50 DIN Rail Mounting for TB50

Mon, 30 Apr 2012 16:06:03 +1000

This is the PC50 DIN Rail Mounting for the TB50 Terminal Card which comes with SMC-202Price: $29.00

SMC-203 PC68 DIN Rail Mounting for TB68

Mon, 30 Apr 2012 16:01:29 +1000

This is the PC68 DIN Rail Mounting for the TB68 Terminal Card which comes with SMC-200Price: $29.00

AXS-4323 CPVC+PP Clamp Saddles(SCH80) DN100

Mon, 30 Apr 2012 11:05:48 +1000

CPVC+PP Clamp Saddles for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 100mm

Manufacturers Part No. SLCS-C40

Download Datasheet

Price: $99.00

AXS-4322 CPVC+PP Clamp Saddles(SCH80) DN80

Mon, 30 Apr 2012 10:58:38 +1000

CPVC+PP Clamp Saddles for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 80mm

Manufacturers Part No. SLCS-C30

Download Datasheet

Price: $92.50

AXS-4320 CPVC+PP Clamp Saddles(SCH80) DN50

Sun, 29 Apr 2012 11:52:52 +1000

CPVC+PP Clamp Saddles for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 50mm

Manufacturers Part No. SLCS-C20

Download Datasheet

Price: $76.95

AXS-4318 CPVC Tee Fitting DN100

Sun, 29 Apr 2012 11:43:30 +1000

CPVC Tee Fitting for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 100mm

Manufacturers Part No. SLTF-T40

Download Datasheet

Price: $176.95

AXS-4317 CPVC Tee Fitting DN80

Sun, 29 Apr 2012 11:37:20 +1000

CPVC Tee Fitting for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 80mm

Manufacturers Part No. SLTF-T30

Download Datasheet

Price: $139.95

AXS-4315 CPVC Tee Fitting DN50

Sun, 29 Apr 2012 11:29:10 +1000

CPVC Tee Fitting for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 50mm.

Manufacturers Part No. SLTF-T20

Download Datasheet
Price: $89.95

AXS-4312 CPVC Tee Fitting DN25

Fri, 27 Apr 2012 17:04:41 +1000

CPVC Tee Fitting for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415. DN size 25mm

Manufacturers Part No. SLTF-T10

Download Datasheet

Price: $54.95

AXS-4301 CPVC Glue-On Adapters

Fri, 27 Apr 2012 16:32:36 +1000

CPVC Glue-On Adapters for the Paddle Wheel Flow Sensors AXS-400, AXS-410 and AXS-415

Download Datasheet

Price: $39.00

AXS-415 Paddle Wheel Flow Controller Meter

Fri, 27 Apr 2012 15:47:32 +1000

These are a great economical paddle wheel flow sensor with a LED display, 2 alarm relays and totaliser pulse (NPN Open Collector) output. Of polypropylene construction they can operate over a temperature range of -10 to 85degC

Features:

Auto change red or green on alarm status change
Accuracy0.75% of full scale
Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch)
Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s)
Field-rangable supply voltage from 14 to 28 VDC
Display flow units Litre, Gal,Cub metre,
Dual alarm function
16 bit DAC 4-20mA analog output
Field-rangable operating temperature from -10 to 85C
Protection class NEMA4 (IP65)
CE EMC certification

Specifications:

Power Supply:	14 to 28 VDC +/-5%(<5mA)
Measuring Accuracy:	0.75% Full scale
Repeatability:	0.5% Full scale
Readout range:	0-99999 adjustable (rate) 0-99999999 adjustable (totalizer)
Output Frequency:	60.5Hz per m/s nominal
Relay Output:	AC250V-5A, DC30V-7A
Relay Output mode:	Hi or Lo adjustable
Sensor Body Material	Polypropylene
Rotor Material:	PFA + Magnetic
Shaft and bearings material:	Zirconia Ceramic and Stainless Steel
O-rings material:	FKM (viton)
Electrical Connection:	8 m Cable IP68
Cable Type:	3 conductor + shield
Pressure Port Material:	Stainless steel 1.4401
Reverse Voltage Protection:	Included as standard
Measuring Kinematic viscosity range:	0.5 to 20 centi stokes (cst)
Sensor length:	68.5 mm
Manufacturer Part:	SL2-P0-20NTF8

Documents:

Download Datasheet

Download Manual

Price: $299.00

BAT-010 JST Right-Angle Connector - Through-Hole 2-Pin

Fri, 27 Apr 2012 15:30:23 +1000

This is a 2-pin, through-hole PH series JST connector. The pins are spaced by 2mm.

We really like the solid locking feeling and high current rating on these small connectors. This connector will mate with all of our LiPo batteries.

Documents: Datasheet

Price: $1.00

BOK-012 Making Android Accessories with IOIO

Fri, 27 Apr 2012 15:21:47 +1000

The Android operating system is becoming more and more popular among embedded device manufacturers making it evermore practical to create devices that can interface with Android. Now you can create your own electronic devices with the popular IOIO ("yoyo") board, and control them with your Android phone or tablet. With this concise guide, youll get started by building four example projectsafter that, the possibilities for making your own fun and creative accessories with Android and IOIO are endless.

To build Android/IOIO devices, you write the program on your computer, transfer it to your Android, and then communicate with the IOIO via a USB or Bluetooth connection. The IOIO board translates the program into action. This book provides the source code and step-by-step instructions you need to build the example projects. All you have to supply is the hardware.

The shopping list of the hardware used in the book can be found here.

Features:

Learn your way around the IOIO and discover how it interacts with your Android
Build an intruder alarm that sends a text message when it detects movement
Make a temperature sensing device that logs readings on your Android
Create a multicolor LED matrix that displays a Space Invader animation
Build an IOIO-powered surveillance rover that you control with your Android
Get the software and hardware requirements for creating your own Android/IOIO accessories

Info:

Publisher: O'Reilly Media
ISBN-10: 1449323286
ISBN-13: 978-1449323288
Product Dimensions: 8.3 x 5.3 x 0.3 inches

Price: $9.95

AXS-410 Paddle Wheel Flow Controller Meter

Fri, 27 Apr 2012 14:41:49 +1000

These are a great economical paddle wheel flow sensor with a LED display, 2 alarm relays and 4-20mA analog output. Of polypropylene construction they can operate over a temperature range of -10 to 85degC

Features:

Auto change red or green on alarm status change
Accuracy0.75% of full scale
Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch)
Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s)
Field-rangable supply voltage from 14 to 28 VDC
Display flow units Litre, Gal,Cub metre,
Dual alarm function
16 bit DAC 4-20mA analog output
Field-rangable operating temperature from -10 to 85C
Protection class NEMA4 (IP65)
CE EMC certification

Specifications:

Power Supply:	14 to 28 VDC +/-5%(<5mA)
Measuring Accuracy:	0.75% Full scale
Repeatability:	0.5% Full scale
Readout range:	0-99999 adjustable (rate) 0-99999999 adjustable (totalizer)
Output Frequency:	60.5Hz per m/s nominal
Relay Output:	AC250V-5A, DC30V-7A
Relay Output mode:	Hi or Lo adjustable
Sensor Body Material	Polypropylene
Rotor Material:	PFA + Magnetic
Shaft and bearings material:	Zirconia Ceramic and Stainless Steel
O-rings material:	FKM (viton)
Electrical Connection:	8 m Cable IP68
Cable Type:	3 conductor + shield
Pressure Port Material:	Stainless steel 1.4401
Reverse Voltage Protection:	Included as standard
Measuring Kinematic viscosity range:	0.5 to 20 centi stokes (cst)
Sensor length:	68.5 mm
Manufacturer Part:	SL2-P0-22NNF8

Documents:

Download Datasheet

Download Manual

Price: $319.00

AXS-400 Paddle Wheel Flow Sensor

Fri, 27 Apr 2012 11:14:24 +1000

These are a great economical paddle wheel flow sensor with a NPN transistor output. Of polypropylene construction they can operate over a temperature range of -10 to 85degC

Features:

Accuracy0.75% of full scale
Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch)
Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s)
Field-rangable supply voltage from 5 to 24 VDC
Field-rangable operting temperature from -10 to 85C
Protection class NEMA6,6P(IP68)
CE EMC certification

Specifications:

Power Supply:	5 to 24 VDC +/-5%(<5mA)
Measuring Accuracy:	0.75% Full scale
Repeatability:	0.5% Full scale
Pipe Size Range:	15 to 100mm (DN15 to DN100)
Output Frequency:	60.5Hz per m/s nominal
Pulse Output Type:	Transistor NPN open collector (<30mA)
Storage Temp:	-30 to 90degC
Sensor Body Material	Polypropylene
Rotor Material:	PFA + Magnetic
Shaft and bearings material:	Zirconia Ceramic and Stainless Steel
O-rings material:	FKM (viton)
Electrical Connection:	8 m Cable IP68
Cable Type:	3 conductor + shield
Pressure Port Material:	Stainless steel 1.4401
Reverse Voltage Protection:	Included as standard
Measuring Kinematic viscosity range:	0.5 to 20 centi stokes (cst)
Sensor length:	68.5 mm
Manufacturer Part:	SL-P0EF

Documents:

Download Datasheet

Download Manual

Price: $239.00

SFM-002 Bipolar Stepper Motor 42BYGHM809

Thu, 26 Apr 2012 15:18:42 +1000

These steppers are a great way to get things moving, especially when positioning and repeatability is a concern.

Features:

Step Angle (degrees) : 0.9
2-Phase
Rated Voltage: 3V
Rated Current: 1.7A/Phase
5mm Diameter Drive Shaft
Holding Torque: 48N.cm
NEMA 17 form factor

Documents:

Datasheet

Price: $19.95

GPS-0031 Venus GPS Logger with SMA Connector

Thu, 26 Apr 2012 15:01:38 +1000

Replaced with GPS-003
This is one of the smallest and most powerful GPS loggers on the market. The Venus GPS module can be configured to an amazingly powerful 10Hz update rate, with 14 channel tracking and can store up to 32Mbits of GPS data! Boasting 28mA operating current, and high sensitivity, this receiver seriously opens new doors for tracking. Module outputs the standard NMEA-0183 or SkyTraq Binary sentences at a default rate of 9600bps (adjustable to 115200bps).

The Venus634LPx has improved sensitivity, an integrated LNA (with multipath detection and suppression), built-in RTC, and integrated single power supply making it very simple to use. In addition, the module supports data logging with an external SPI Flash!

The logger's SPI Flash can be configured over the TX and RX pins using our USB to Serial FT232 Breakout Board.

Check out our GPS buying guide!

Features:

51 channel acquisition and 14 channel tracking
SkyTraq based chipset
10Hz max update rate (1Hz default)
Integrated LNA
Single 2.7-3.3V supply
3.3V TTL UART
32Mbits of flash space
Power: 28mA tracking
Sensitivity: -161dBm
Accuracy: <2.5m
Hot start: 1 Seconds
Cold Start: 29 Seconds
Supports active or passive antennas
Supports SBAS (WAAS, EGNOS, MSAS)

Dimensions: 1.25 x 0.75 inches

Documents:

Price: $59.95

TOD-063 RS-232 to Single-Mode Fibre Converter with SC Connectors

Fri, 20 Apr 2012 17:07:04 +1000

Please note these converters are sold individually. Two converters are required to form an end-to-end link.

The 3onedata Model 277A-S-SC-20KM serial fibre converter provides a cost effective plug-and-play solution for long-range serial extensions. These converters are ultra-miniature in size and feature pluggable screw terminals for serial interfaces and SC style fibre-optic connections.

Features:

Auto sense serial signal rate, zero delay automatic transmit
120 kbps the highest rate
Standard RS-232 DE-9 Female interface
Up to 20 km fibre communication distance with single-mode fibres

Documents:

Download Datasheet

Download Manual

Specifications:

Serial Interface:
Standard:	RS-232
RS-232 Connections:	In, Out, Gnd
Connection type:	Female DE-9
Baudrate:	0 to 120 kbps
Surge Protection:	600 W
ESD Protection:	15 kV

Fibre Interface:
Transmission mode:	Single-mode
Wavelength:	1310 nm
Fibre Type:	8.3/125, 8.7/125, 9/125, or 10/125 μ
Fibre Connections:	In, Out
Connector Type:	Dual SC connector

Converter:
Power:	5 VDC (240 VAC Plug pack included)
Power Connectors:	DC Jack
Power Consumption:	2 W
Working Temperature:	-10 to 60 °C
Storage Temperature:	-40 to 85 °C
Working Humidity:	5% to 95%
Dimensions:	100 × 69 × 22 mm
Case:	Steel

Price: $289.00

TOD-062 RS-232 to Multi-Mode Fibre Converter with ST Connectors

Fri, 20 Apr 2012 17:02:55 +1000

Please note these converters are sold individually. Two converters are required to form an end-to-end link.

The 3onedata Model 277A-M-ST-2KM serial fibre converter provides a cost effective plug-and-play solution for long-range serial extensions. These converters are ultra-miniature in size and feature pluggable screw terminals for serial interfaces and ST style fibre-optic connections.

Features:

Auto sense serial signal rate, zero delay automatic transmit
120 kbps the highest rate
Standard RS-232 DE-9 Female interface
Up to 2 km fibre communication distance with multi-mode fibres

Documents:

Download Datasheet

Download Manual

Specifications:

Serial Interface:
Standard:	RS-232
RS-232 Connections:	In, Out, Gnd
Connection type:	Female DE-9
Baudrate:	0 to 120 kbps
Surge Protection:	600 W
ESD Protection:	15 kV

Fibre Interface:
Transmission mode:	Multi-mode
Wavelength:	1310 nm
Fibre Type:	50/125, 62.5/125, or 100/140 μm
Fibre Connections:	In, Out
Connector Type:	Dual ST connector

Converter:
Power:	5 VDC (240 VAC Plug pack included)
Power Connectors:	DC Jack
Power Consumption:	2 W
Working Temperature:	-10 to 60 °C
Storage Temperature:	-40 to 85 °C
Working Humidity:	5% to 95%
Dimensions:	100 × 69 × 22 mm
Case:	Steel

Price: $249.00

TOD-065 RS-232/485/422 to Single-Mode Fibre Converter with SC Connectors

Fri, 20 Apr 2012 16:53:17 +1000

Please note these converters are sold individually. Two converters are required to form an end-to-end link.

The 3onedata Model 277-S-SC-20KM serial fibre converter provides a cost effective plug-and-play solution for long-range serial extensions. These converters are ultra-miniature in size and feature pluggable screw terminals for serial interfaces and SC style fibre-optic connections.

The Model 277 Series incorporates a method for automatically detecting the serial signal baud rate by hardware. This is an extremely convenient feature for the user. Even if a device's baud rate is changed, the signal will still be transmitted through the RS-232 or RS-422/485 to fibre converter without any problem. The converter also automatically converts between the half duplex RS-485 and full duplex RS-232 and RS-422 interfaces.

Features:

Auto sense serial signal rate, zero delay automatic transmit
500 kbps the highest rate
Supply three interface (RS-232/485/422)
Up to 20 km fibre communication distance with single-mode fibres

Documents:

Download Datasheet

Download Manual

Specifications:

Serial Interface:
Standard:	RS-232, RS-485 and RS-485
RS-232 Connections:	In, Out, Gnd
RS-485 Connections:	D+, D-, Gnd
RS-422 Connections:	R+, R-, T+, T-, Gnd
Connection type:	Pluggable screw terminals
Baudrate:	0 to 500 kbps
RS-485 Direction Control:	Automatic
Surge Protection:	600 W
ESD Protection:	15 kV

Fibre Interface:
Transmission mode:	Single-mode
Wavelength:	1310 nm
Fibre Type:	8.3/125, 8.7/125, 9/125, or 10/125 μm
Fibre Connections:	In, Out
Connector Type:	Dual SC connector

Converter:
Power:	9 to 36 VDC
Power Connectors:	Pluggable screw terminals
Power Consumption:	2 W
Working Temperature:	-10 to 60 °C
Storage Temperature:	-40 to 85 °C
Working Humidity:	5% to 95%
Dimensions:	100 × 69 × 22 mm
Case:	Steel

Price: $319.00

TOD-064 RS-232/485/422 to Multi-Mode Fibre Converter with ST Connectors

Fri, 20 Apr 2012 16:47:25 +1000

Please note these converters are sold individually. Two converters are required to form an end-to-end link.

The 3onedata Model 277-M-ST-2KM serial Fibre converter provides a cost effective plug-and-play solution for long-range serial extensions. These converters are ultra-miniature in size and feature pluggable screw terminals for serial interfaces and ST style fibre-optic connections.

Features:

Auto sense serial signal rate, zero delay automatic transmit
500Kbps the highest rate
Supply three interface (RS-232/485/422)
Up to 2 km fibre communication distance with multi-mode fibres

Documents:

Download Datasheet

Download Manual

Specifications:

Serial Interface:
Standard:	RS-232, RS-485 and RS-485
RS-232 Connections:	In, Out, Gnd
RS-485 Connections:	D+, D-, Gnd
RS-422 Connections:	R+, R-, T+, T-, Gnd
Connection type:	Pluggable screw terminals
Baudrate:	0 to 500 kbps
RS-485 Direction Control:	Automatic
Surge Protection:	600 W
ESD Protection:	15 kV

Fibre Interface:
Transmission mode:	Multi-mode
Wavelength:	850 nm
Fibre Type:	50/125, 62.5/125, or 100/140 μm
Fibre Connections:	In, Out
Connector Type:	Dual ST connector

Converter:
Power:	9 to 36 VDC
Power Connectors:	Pluggable screw terminals
Power Consumption:	2 W
Working Temperature:	-10 to 60 °C
Storage Temperature:	-40 to 85 °C
Working Humidity:	5% to 95%
Dimensions:	100 × 69 × 22 mm
Case:	Steel

Price: $289.00

TOD-084 Ethernet to Optic Fibre Multi Mode, Dual Fibre, 2 km, ST Connector

Fri, 20 Apr 2012 15:12:32 +1000

The 3onedata Model 1100-ST-2KM Ethernet Fiber converter pair provide a cost effective plug-and-play solution for long-range 10Base-T or 100Base-TX Ethernet extensions and added benefit of 10/100 auto-negotiation, making it the perfect choice when planning future upgrades of 10Base-T networks. These converters are ultra-miniature in size and feature a shielded RJ45 Ethernet jack and ST style fiber-optic connections. Built-in auto-sensing capabilities enable full or half-duplex Ethernet operation with no configuration required!

Features:

Meets IEEE802.3, IEEE802.3u 10Base-T, 100Base-TX, 100Base-FX standards
MDI/MDI-X auto negotiation, 10M/100M auto negotiation
Supports full-duplex/halfduplex, Point-to-point transparent transfer
Powered at 5 VDC power and includes plug pack adapter
Plug and Play, easy to install

Documents:

Download datasheet

Download manual

Specifications:

Transmission Distance:	2 km
Fibre Connection:	ST connector
Wavelength:	1310 nm
Input Voltage:	5 VDC (240V plugpack included)
Power Consumption:	4 W
Operating temperature:	-10 to 65 C
Storage temperature:	-20 to 70 C
Relative humidity:	5% to 95%
Dimensions:	160.5 110 30 mm
Case:	Iron

Price: $119.00

HYS-0011 Hydreon RG-11 Optical Rain Sensor with 6 Digit Counter

Fri, 20 Apr 2012 14:08:46 +1000

We have combined the Hydreon RG-11 Optical Rain Sensor with a Novus 6 Digit Counter. With the RG-11 operating in the tipping rain bucket mode the counter will display the amount of rain that has fallen since the last reset. A modbus RS-485 interface on the counter allows a PLC or SCADA host to communicate with the counter to access rain data.

The RG-11 Rain Gauge senses water hitting its outside surface using beams of infrared light. It uses the same sensing principle used in millions of automotive rain sensing windshield wiper controls.

The RG-11 is optical - not mechanical, chemical, or conductive. Consequently, it is far more rugged, sensitive and reliable than any other technology. The sensor is extremely sensitive, and virtually immune to false trips. Yet, it is completely unaffected by jostling and motion. There are no exposed conductors to corrode, and no openings for bugs to crawl into. There is no place for leaves or other debris to collect.

The RG-11 Rain Sensor includes a DIP switch that allows it to be set up for the mode of operation that best matches the application.

RG-11 Modes of Operation:

Tipping Bucket Emulation-- Replace your tipping bucket with a low maintenance alternative.
"It's Raining"-- Close a skylight at the first sign of rain, and open it when it stops raining.
Condensation / Frost Sensing
Wiper control
Irrigation Control-- No more watering during a downpour!
Drop Detection

Documents:

Download Manual

Price: $199.95

HYS-001 Hydreon RG-11 Optical Rain Sensor

Tue, 17 Apr 2012 10:04:13 +1000

The RG-11 Rain Gauge senses water hitting its outside surface using beams of infrared light. It uses the same sensing principle used in millions of automotive rain sensing windshield wiper controls.

The RG-11 Rain Sensor includes a DIP switch that allows it to be set up for the mode of operation that best matches the application.

RG-11 Modes of Operation:

Tipping Bucket Emulation-- Replace your tipping bucket with a low maintenance alternative.
"It's Raining"-- Close a skylight at the first sign of rain, and open it when it stops raining.
Condensation / Frost Sensing
Wiper control
Irrigation Control-- No more watering during a downpour!
Drop Detection

Documents:

Download Manual

Price: $84.95

DEC-026 DVP-28SV11T Programmable Logic Controller

Thu, 12 Apr 2012 17:18:26 +1000

The DVP-SV Series is a highly expandable series industrial PLCs. The DVP-28SV11T has expansion ports on both sides. Expansion modules can be mounted on the left (high speed expansion) or right (low speed general purpose modules) of the PLC without external wiring.

The unit features a rich command set with PID loops for process control, linear / arc interpolation commands and high speed counters. Two small potentiometers on the front of the unit can be read as analog inputs with 8-bit resolution.

The programming software runs on Windows and is freely available for download.

Specifications:

Power:	20.4 to 28.8 VDC
Digital Inputs:	2 banks of 8 inputs, 24 VDC sink or source
Digital Outputs:	12 NPN Open collector outputs with shared commons
Output Rating:	0.3 A each point
Communication Port:	RS-232 and RS-485, Modbus ASCII/RTU master or slave
Program Capacity:	16k steps
Execution Speed:	0.24 s per basic instruction
IO Points:	Up to 512 via expansion modules
High Speed Counters:	4 counters, 200 kHz

Note 1: Each bank of digital inputs can be wired so all inputs in the bank are NPN or all are PNP type inputs.

Applications:

2-axis servo positioning control, material cutting machine (high-speed servo control), main hoist of crane, material clip controlled by servo, equipments in the optoelectronics industry, semiconductor industry, textile industry, energy saving activities and automation in buildings.

Resources:

Programming Service:

Do you have an application for one of our PLCs but don't know how to program in Ladder Logic? We can program it for you. Email us your requirements and we will provide a quote to do the programming.

Price: $399.00

DEC-016 DVP-14SS211T Programmable Logic Controller

Thu, 12 Apr 2012 16:26:09 +1000

The DVP-SS2 Series is Delta Electronics' second generation of slimline industrial PLCs. The DVP-14SS211T features high speed counters and pulse outputs, a flexible serial port, real-time monitoring and an expansion bus that allows matching modules to be mounted on the right side of the PLC without external wiring.

The DVP-14SS211T supports PID loops with automatic tuning for process control applications. The transistor outputs allow high speed pulse generation for servo or stepper motor motion control applications.

The programming software runs on Windows and is freely available for download.

Specifications:

Power:	20.4 to 28.8 VDC
Digital Inputs:	8 inputs, 24 VDC sink or source
Digital Outputs:	6 open collector type transistor outputs
Output Rating:	30 VDC, 500 mA each output
Communication Port:	RS-232 and RS-485, Modbus ASCII/RTU master or slave
Program Capacity:	8k steps
IO Points:	Up to 238 via expansion modules
Software Up/Down Counters:	Any input, up to 10 kHz on a single input
Software Quadrature Inputs:	2 - X4/X5 (5 kHz) and X6/X7 (5 kHz)
Hardware Up/Down Counters:	2 - X0 and X2, both 20 kHz
Hardware Quadrature Inputs:	2 - X0/X1 and X2/X3, both 10 kHz
Hardware Pulse/PWM Outputs:	4 - Y0 to Y3 each up to 10 kHz

Note 1: The digital inputs can be wired so all are NPN or all are PNP type inputs.

Applications:

Spinning machine, conveyer belt (rotation speed control), winding machine (tension control). Used for PID temperature/humidity control, 2-axis AC motor drive constant speed control, temperature control using a analog signal monitoring of a whole factory. (PLC EASY LINK).

Resources:

Programming Service:

Do you have an application for one of our PLCs but don't know how to program in Ladder Logic? We can program it for you. Email us your requirements and we will provide a quote to do the programming.

Price: $149.00

DEC-006 DVP-20SX211T Programmable Logic Controller

Thu, 12 Apr 2012 16:15:42 +1000

The DVP-SX2 Series is Delta Electronics' second generation of slimline industrial PLCs. The DVP-20SX211T features built-in analog inputs, analog outputs, high speed counters and pulse outputs, a flexible serial port and expansion ports on both sides. Expansion modules can be mounted on the left (high speed expansion) or right (low speed general purpose modules) of the PLC without external wiring.

Two small potentiometers on the front of the unit can be read as an additional 2 analog inputs with 8-bit resolution. The DVP-20SX211T supports PID loops with automatic tuning for process control applications.

The programming software runs on Windows and is freely available for download.

Specifications:

Power:	20.4 to 28.8 VDC
Digital Inputs:	8 24 VDC sink or source
Digital Outputs:	6 x NPN Open Collector Outputs
Output Rating:	0.5 A each point
Analog Inputs:	4 10 VDC or 20 mA (inc. 4 to 20 mA)
Analog Input Resolution:	12 bit (5 mV / 10 A)
Analog Output:	2 10 VDC or 20 mA (inc. 4 to 20 mA)
Analog Output Resolution:	12 bit (5 mV / 10 A)
Communication Port:	RS-232 and RS-485, Modbus ASCII/RTU master or slave
Program Capacity:	16k steps
IO Points:	Up to 230 via expansion modules
Software Up/Down Counters:	Any input, up to 10 kHz on a single input
Software Quadrature Inputs:	3 - X0/X2 (15 kHz), X4/X5 (5 kHz) and X6/X7 (5 kHz)
Hardware Up/Down Counters:	2 - X0 and X2, both 100 kHz
Hardware Quadrature Inputs:	2 - X0/X1 and X2/X3, both 10 kHz

Note 1: The digital inputs can be wired so all are NPN or all are PNP type inputs.

Note 2: Effectively ~11 bits in 4 to 20 mA mode

Applications:

Used for PID temperature/humidity control, 2-axis AC motor drive constant speed control, temperature control using a analog signal monitoring of a whole factory. (PLC EASY LINK).

Resources:

Programming Service:

Do you have an application for one of our PLC's but don't know how to program in Ladder Logic? We can program it for you. Email us your requirements and we will provide a quote to do the programming.

Price: $369.00

SFI-002 0-5V Analog Panel Meter

Thu, 12 Apr 2012 15:26:49 +1000

This analog panel meter measures DC voltage from 0-5 volts with 2.5% accuracy. It has a clear and easy to read scale and an adjustable dial. These come in handy for measuring the output of sensors with 5V ranges.

The face of the meter is 45x45mm overall. The mounting hole should be 38mm. The overall depth of the meter is 35mm.

Documents:

Product Sheet

Price: $5.00

KTA-218 Lead-Acid Gel Cell Battery Tester

Tue, 10 Apr 2012 04:36:06 +1000

Many vital pieces of equipment such as Remote Telemetry Units(RTUs), Programmable Logic Units, Weather Stations and Security systems are required to operate 24 hours a day. To prevent cessation of operation in the event of AC mains power failure the equipment is usually fitted with a sealed acid battery and charger. If mains power fails the equipment is then powered off the battery. Typically in the case of security alarms we require the equipment to operate for days and telemetry systems for 6 to 12 hours.

Often though we find sealed lead acid batteries will lose their ability to hold charge over time and when AC power is lost the battery quickly loses it charge and the equipment operates for an unexpectedly short time.

Our KTA218 Battri-Testa allows the battery to be periodically checked under its normal load for a preset time to determine if the battery is likely to meet the required backup time in the near future. It does this by disconnecting mains power and monitoring the battery voltage during the test. If the battery has fallen below a programmable limit then the test has failed and the battery should be replaced.

The results of these tests are logged to non-volatile memory which can be downloaded to a PC at a later date. At the completion of each test the Battri-Tester also calculates an expected lifetime of the battery.

A RTU Modbus RS485 connection allows a RTU or PLC or other controller to communicate with the Battri-Testa. The controller can read the current battery volts, results of the last test and the expected life time of the battery. If the battery has failed the test then it is prevented from carrying out any further tests until a reset is carried out either by the button or remotely via Modbus.

Maintenance crew can begin a test by simply pressing the test button or remotely by a Modbus command. A test will not be allowed to begin if the battery voltage is below a low limit. The battery voltage has to rise and remain above a start limit for a preset time before the test will be allowed to commence.

The setup of the Battri-Testa is done by the free PC Windows Software - Battri-Testa Config via the USB port. The software allows you to configure the Battri-Testa, initiate and monitor tests and upload logged test results. The test results can be viewed in a spreadsheet or as a graph.

Features:

Tests can be started manually by pushbutton
Tests can be done at specified times of day and week or weeks
Tests can be done every specifed number of hours
Results of up to 100 tests logged to memory
Modbus communications. Programable baud rate and parity.
Start Test and Reset button
Battery Fail, Run and Low Battery indicator leds
Expected battery life calculation
Dimensions: 115x90x40 mm

Download Datasheet!

Price: $139.00

TRM-046 SKJ-4RD/X Fuse Terminal

Wed, 04 Apr 2012 16:20:52 +1000

These DIN rail mount fuse terminals include an LED that lights when the fuse is blown, allowing quick diagnosis of problems in the field. Suitable for 24V Power.

Specifications:

Manufacturer Part:	SKJ-4RD/X
Dimensions:	72.5 8.2 56 mm
Rated Voltage:	660 V
Rated Current:	6.3 A
Fuse:	Suits M205 style (not included)
Rigid Cable:	Suits 0.2 to 4 mm² (24 to 12 AWG)
Soft Cable:	Suits 0.2 to 4 mm² (24 to 12 AWG)
Box quantity:	30

Price: $3.12

CMS-129 Wet Bulb Wick

Wed, 04 Apr 2012 15:29:41 +1000

p>This replacement wick keeps the wet sensor of a wet/dry bulb psychrometer moist. It suits our CMS-121 and CMS-123 sensor modules.

Price: $7.95

CMS-123 Wet/Dry-Bulb Psychrometer Humidity Measurement Module 4-20mA

Wed, 04 Apr 2012 15:15:45 +1000

The Comeco RHU is designed to measure relative humidity in air and other gases and gas mixtures utilizing the well-known method of "dry" and "wet" thermometers. It uses 2 identical class 'A' RTD sensors mounted in stainless steel sheaths mounted on a stainless steel plate. The plate can be installed inside or outside drying or moistening chambers. The wet/dry bulb method for determining humidity is especially suitable in areas of high humidity such as fog rooms for horticulture.

The method of "wet/dry temperature difference provides high accuracy in RH measurement. For this accuracy to be ensured, it is absolutely necessary to keep the "wet" sensor always wet and to guarantee the evaporation from its surface. For this purpose, this module is equipped with a special moistening system. It is also important to assure continuous gas movement along the sensors during the measurement process. Together with a COMECO RH-control instrument (RT180 or RT390), RHU can be widely used in areas where standard capacitance RH probes are not applicable: high-temperature chambers, high-accuracy RH measurement, etc.

The formulas for converting wet and dry temperatures to a humidity for air can be found at the 4WX.COM Weather Information Center.

This version of the module includes signal conditioners that convert the Pt100 sensors to 4 to 20 mA outputs. The cheaper CMS-121 version presents the Pt100 sensor signals directly.

Specifications:

Measurement Temperature Range
"Dry" thermometer	Pt100, 4-20mA out
"Wet" thermometer	Pt100, 4-20mA out
Conversion range	0% to 100% RH
External Mounting	-50 to 200 °C
Internal Mounting	-20 to 120 °C
Measurement Accuracy	1% RH
Response Time	2 s
Manufacturer's Part No.	RHUS-BD-TT

Documents:

Datasheet

Price: $399.95

CMI-002 4 to 20 mA Loop Powered 96 � 48 mm Backlight LCD Indicator

Tue, 03 Apr 2012 15:52:01 +1000

The TI200 is a microprocessor-based programmable process indicator, designed especially to be powered from the input current loop. TI200 is equipped with a fully programmable -1999 to 9999 LCD display with programmable point position and digital filter as well as with a 2-key keyboard. Front panel IP65 rated.

The indicator comes in a plastic case for panel mounting in a standard 96 48 mm DIN front size.

Features:

Loop powered
4 to 20 mA input
Programmable display range from -1999 to 9999 with selectable decimal point
13 mm tall LCD digits
Simple configuration with settings stored in non-volatile memory
CE EMC certification

Specifications:

Operating range:	3 to 22 mA
Measurement Range:	4 to 20 mA
Display Range:	-1999 to 9999
Display to Input:	Programmable linear mapping
Decimal Point:	Programmable
Measurement Error:	0.05% or 1 digit
Loop Voltage:	4 to 36 VDC
Display:	4 13 mm tall LCD digits
Operating Range:	-10 to 65 C, 0 to 85% RH
Panel Cutout:	90 42 mm

Manufacturer Part: TL200-H-T-X-X-X-X

Documents:

Download Datasheet

Price: $139.00

CMS-121 Wet/Dry-Bulb Psychrometer Humidity Measurement Module

Tue, 03 Apr 2012 13:54:20 +1000

This version of the module directly presents the Pt100 sensor signals. The CMS-123 includes 4 to 20 mA signal conditioners for each sensor.

The formulas for converting wet and dry temperatures to a humidity for air can be found at the 4WX.COM Weather Information Center.

Specifications:

Measurement Temperature Range
"Dry" thermometer	Pt100
"Wet" thermometer	Pt100
Conversion range	0% to 100% RH
External Mounting	-50 to 200 °C
Internal Mounting	-20 to 120 °C
Measurement Accuracy	1% RH
Response Time	2 s
Manufacturer's Part No.	RHUS-BD-X

Documents:

Datasheet

Price: $299.95

LAJ-039 PS12DC Power Switching Board

Fri, 30 Mar 2012 12:02:19 +1100

The PS12DC is a power switching board designed for medium to low current DC power switching applications. It is suitable for use with the Labjack U3, U6 and UE9 data acquisition modules. Controlled through 12 digital outputs, the board can switch power sources ranging from 5 to 28V DC. Attach the PS12DC to the DB15 connector presented on all compatible devices, and toggle the states of the EIO and CIO digital output lines to turn the switches on/off.

Features:

12 digitally controlled switches with LED indicators
Optical isolation
Handles 5 - 28 Volt supply
Up to 750mA/chan
Resettable fuse protection
Flyback protection

For more information, reference the datasheet.

Price: $89.95

IBS-1301 M30 Shielded Capacitive Proximity Sensor CPS-30NOC15B

Mon, 26 Mar 2012 09:41:15 +1100

Capacitive proximity sensors switch in the presence of metallic and non-metallic objects. These sensors can detect almost any liquids and solids. A small control on the back of the sensor adjusts the triggering threshold. These sensors take 10 to 30 V DC and have both normally open and normally closed PNP-type outputs. The rear of the sensor has an LED indicator that lights when the sensor is triggered.

The sensor has an 30 mm diameter threaded body, allowing easy mounting and adjustment. 15 mm sensing distance.

Specifications:

Manufacturer Part:	IBEST CPS-30NOC15B
Rated operational voltage:	24 V DC
Supply voltage:	10 to 30 V DC
Voltage drop:	≤ 2.0 V
Rated insulation resistance:	≥ 20 MΩ
Load current capacity:	200 mA
Off-state current	≤ 10 mA
Leakage current:	≤ 20 A
Protection:	Reverse polarity
Repeated accuracy:	≤ 5%
Ambient temperature range:	-25 to 70 C
Frequency:	30 Hz
Function indication:	Red LED
IP ratings:	IP67
Housing material:	Nickle plated brass
Material of sensing face:	ABS
Connection:	Bare wire
No. of wires gauge:	4 0.16 mm
Cable Length:	2 m
Detection distance:	0...13.5 mm
Approvals:	CE

Documents:

Download Product Part Number Guide

Download IBEST Capacitive Proximity Sensors Datasheet

Price: $59.00

KTL-250-BL 24V Anemometer Interface with LCD and 64K Logging

Thu, 22 Mar 2012 16:19:46 +1100

The KTA-250 is an anemometer monitoring and alarming card. It allows the wind speed and direction to be measured with a Davis Instruments DS7911 Anemometer, without the need for the entire weather station.

Monitoring of the wind speed and direction can be done via the analog retransmission channels with 0-5V, 1-5V, 0-20mA or 4-20mA outputs. As well as monitoring the speed and direction, 2 alarm relays can be programmed to activate at a certain speed or wind direction range, or combination of the two. Wind speed and direction can also be monitored using the Modbus protocol with either USB or 2-wire RS-485 connection. All settings are set using the Modbus protocol and the provided software.

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

We supply a software configuration package called "KTA-250 Configurator" which is a simple to use program. The configuration software allows the user to monitor the wind speed and direction, as well as the maximum and minimum speeds, and allows the user to configure all the available settings.

Downloads:

Price: $399.00

KTL-250-AL 12V Anemometer Interface with LCD and 64K Logging

Thu, 22 Mar 2012 16:17:40 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $399.00

KTA-250-BL 24V Anemometer Interface with 64K Logging

Thu, 22 Mar 2012 16:16:11 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $349.00

KTA-250-AL 12V Anemometer Interface with 64K Logging

Thu, 22 Mar 2012 16:14:09 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $349.00

KTL-250-BX 24V Anemometer Interface with LCD

Thu, 22 Mar 2012 16:10:10 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $229.00

KTL-250-AX 12V Anemometer Interface with LCD

Thu, 22 Mar 2012 15:28:33 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $229.00

FRA-016 Freetronics LeoStick (Arduino Compatible)

Thu, 22 Mar 2012 11:42:39 +1100

The LeoStick is designed to be functionally similar to the upcoming Arduino Leonardo, but given the "honey, I shrunk the kids" treatment!
Just pop it into your USB port (no cable required!) and upload straight from the Arduino IDE. We've even included on-board RGB LED lights and a speaker in this handy sized board. All the usual Arduino pins are present and each LeoStick comes with low profile header sockets for plugging in modules, shields and wires.

Features of the LeoStick include:

Native USB port built-in, no need for any USB or FTDI cables
Two Full Color RGB LEDs on-board! Drive different colored outputs and fun feedback from your sketch right away. One RGB LED is completely programmable, the other does Power, USB RX and TX indication, the RX and TX LEDs can also be controlled.
On-board Piezo speaker element, play sounds, tunes and beeps. Can also be used as a knock/vibration sensor
Same I/O pins. The LeoStick provides all the same header connections as larger boards, you can connect all the same sensors, actuators, and other inputs and outputs as typical Arduino models.
Breadboard compatible, has 0.1" pitch pads and header pins can be fitted underneath
500mA polyfuse and protection on the USB port
ATmega32U4 microcontroller, Arduino compatible with on-board USB, 32K Flash, 2.5K RAM, 1K EEPROM at 16MHz
ISP 6-pin connector for advanced programming of the ATmega32U4 MCU

Getting to know your LeoStick

We have an active community forum here for fun LeoStick programs, installation and setup tips.
Our usual Getting Started guide page is here, including the first setup of the Arduino 1.0 IDE for beta Leonardo support.

Please note: The LeoStick currently uses a modified beta version of the upcoming Arduino Leonardo bootloader. There are some known issues with Windows 7 64-bit drivers and some library functions don't work perfectly yet.

Any firmware or Arduino Leonardo compatible support should not be considered to be final release firmware or in any way an official Arduino. Don't hassle the Arduino team with support or requests related to this board: they're solely our responsibility.

The LeoStick is also a very complete ATmega32U4 breakout and USB board by itself and the LeoStick can be programmed directly from the supplied standard ISP header by AVR Studio, Mac OSX-AVR, avrdude, WinAVR etc.

Resources

Price: $27.23

WIR-034 RF Link Receiver

Thu, 22 Mar 2012 11:31:31 +1100

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only receivers, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair.

Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and don't have IDs. Therefore, a method of filtering this noise and pairing transmitter and receiver will be necessary. The example code below shows such an example for basic operation. Please refer to the example code and links below for ways to accomplish a robust wireless data link.

Features:

434 MHz
500ft range (given perfect conditions)
4800bps data rate
5V supply voltage

Documents:

Price: $6.50

WIR-033 RF Link Transmitter - 434MHz

Thu, 22 Mar 2012 11:25:53 +1100

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair.

Features:

434 MHz
500ft range (given perfect conditions)
4800bps data rate
5V supply voltage

Documents:

Price: $5.00

SFA-304 RFM22 Shield

Thu, 22 Mar 2012 11:08:09 +1100

The RFM22 is a low-cost ISM FSK transceiver module which offers communication at 433MHz ISM and adjustable output power of up to +20 dBm. What does that mean for you? It means your Arduino now has an inexpensive way to talk to other Arduinos so building point-to-point and even basic mesh networks just got a lot more attractive.

The RFM22 Shield connects the RFM22 module to the appropriate lines on the Arduino. By using the RF22 Library, you can send and receive messages via standard 4-wire SPI. The library includes command structures for setting up anything from simple non-addressed point-to-point communication to fully addressed networks of clients and routers. The shield also provides a through-hole antenna connection for hooking up a basic wire antenna. In our testing, a 17cm wire attached to the 'ANT' pin worked just fine. A hole is drilled next to the 'ANT' pin for strain relief.

The shield has on-board power regulation and level shifting. There are one pin headers and jumpers on the interrupt (nIRQ), interface select (nSEL), shutdown input (SDN) and GPIO2 lines so that you can cut the trace and reroute those lines if you need to for your project. The board also provides a little bit of prototyping space.

Features:

Frequency Range = Software configurable from ~240MHz to 980MHz
Sensitivity = -118 dBm
+17 dBm Max Output Power (Configurable)
Data Rate = 1 to 128 kbps
Digital RSSI
Wake-on-radio
Configurable packet structure
Preamble detector
TX and RX 64 byte FIFOs
Low battery detector
Temperature sensor and 8-bit ADC
-40 to +85 C temperature range

Documents:

Price: $29.00

SFR-251 RFM22B-S2 RF Transceiver Breakout Board

Thu, 22 Mar 2012 10:54:51 +1100

Here is the breakout board for the RFM22B which gives you access to the pins. The RFM22B is a low-cost ISM (industrial, scientific, and medical) FSK (frequency-shift keying) transceiver module which offers communication at 434MHz and adjustable output power of up to +17 dBm. The wide operating voltage range of 1.83.6 V and low current consumption makes the RFM22 an ideal solution for battery powered applications.

Communication with the RFM22B is achieved via a standard 4-wire SPI interface. Three configurable general purpose I/Os are also available, the use of which can be tailored towards the needs of your project. A host of other features are also available including an 8-bit ADC, temperature sensor, RX and TX FIFOs, and low-battery detection. See the datasheet below for a complete description of every register and command.

In our testing, a 17cm wire attached to the 'ANT' pin worked just fine. A hole is drilled next to the 'ANT' pin for strain relief.

Features:

Frequency Range = 434 MHz
Sensitivity = -118 dBm
+17 dBm Max Output Power (Configurable)
Low Power Consumption
Data Rate = 1 to 128 kbps
Power Supply = 1.8 to 3.6 V
Ultra low power shutdown mode
Digital RSSI
Wake-on-radio
Auto-frequency calibration (AFC)
Configurable packet structure
Preamble detector
TX and RX 64 byte FIFOs
Low battery detector
Temperature sensor and 8-bit ADC
-40 to +85 C temperature range
Integrated voltage regulators
Frequency hopping capability
FSK, GFSK, and OOK modulation
Low BOM
Power-on-reset (POR)

Dimensions: 0.63x0.63in (16x16mm)

Documents:

Price: $23.00

NOR-113 TM-619-24 Weekly Timer 230 VAC on DIN Rail Mount

Wed, 21 Mar 2012 12:01:52 +1100

The TM-619 is a weekly timer cabale of switching a large load at pre-programmed times during the week.

The timer can hold 8 programs. Each program has an on and off time, and can be set to be active on one of the following patterns of days of the week:

The timer has spade-type connectors for power and relay contacts. It comes with suitable matching cable crimps. (pictured coming out of the top of the unit)

These timers find broad application in heating and refrigerating systems, boilers, ovens, dryers, defrosting equipment, swimming pools, hatcheries, illumination, etc

Features:

Relay Output: 16 A SPDT @ 250 VAC
230 VAC powered
Day and week clock
High contrast LCD
8 programs with combinations: every day the same, every day different, from Monday to Friday, from Sat. to Sun., 3 alternate days
Battery backup for power failure
Reset function and manual override
Dimensions: 60 60 34 mm
Flush panel or wall mounting

Documents:

Download Manual

Price: $54.95

NOR-111 TM-619-24 Weekly Timer 230 VAC

Wed, 21 Mar 2012 11:52:14 +1100

The TM-619 is a weekly timer cabale of switching a large load at pre-programmed times during the week.

The timer can hold 8 programs. Each program has an on and off time, and can be set to be active on one of the following patterns of days of the week:

The timer has spade-type connectors for power and relay contacts. It comes with suitable matching cable crimps. (pictured coming out of the top of the unit)

These timers find broad application in heating and refrigerating systems, boilers, ovens, dryers, defrosting equipment, swimming pools, hatcheries, illumination, etc

Features:

Relay Output: 16 A SPDT @ 250 VAC
230VAC powered
Day and week clock
High contrast LCD
8 programs with combinations: every day the same, every day different, from Monday to Friday, from Sat. to Sun., 3 alternate days
Battery backup for power failure
Reset function and manual override
Dimensions: 60 60 34 mm
Flush panel or wall mounting

Documents:

Download Manual

Price: $49.95

ATO-148 DB9 To 5 Screw Terminal Board

Mon, 19 Mar 2012 16:40:12 +1100

p>DB-9 to 5 Screw Terminal Board. Suitable for Serial to Ethernet Gateways SE5001 and SE5002 for RS-422/485 connections.

Price: $14.95

POL-1110 Qik 2s9v1 Dual Serial Motor Controller

Fri, 16 Mar 2012 15:05:53 +1100

The qik 2s9v1 is Pololus second-generation dual serial motor controller. The compact module allows any microcontroller or computer with a serial port (external RS-232 level converter required) or USB-to-serial adapter to easily drive two small, brushed DC motors with full direction and speed control. It provides ultrasonic, 8-bit PWM speed control via an advanced, two-way serial protocol that features automatic baud rate detection up to 38.4 kbps and optional CRC error checking. Two status LEDs give visual feedback about the serial connection and any encountered error conditions, making debugging easy, and a demo mode allows easy verification of proper operation.

The improvements over the previous generation and competing products include:

high-frequency (ultrasonic) PWM to eliminate switching-induced motor shaft hum or whine
a robust, high-speed communication protocol with user-configurable error condition response
visible LEDs and a demo mode to help troubleshoot problematic installations
reverse power protection on the motor supply (not on the logic supply)

Main Features of the Qik 2s9v1:

Simple bidirectional control of two DC brush motors.
4.5 to 13.5 V motor supply range.
1 A maximum continuous current per motor (3 A peak).
2.7 to 5.5 V logic supply range.
Logic-level, non-inverted, two-way serial control for easy connection to microcontrollers or robot controllers.
Optional automatic baud rate detection.
Two on-board indicator LEDs (status/heartbeat and serial error indicator) for debugging and feedback.
Serial error output to make it easier for the main controller to recover from a serial error condition.
Jumper-enabled demo mode allows initial testing without any programming.
Optional CRC error detection eliminates serial errors caused by noise or software faults.
Optional motor shutdown on serial error or timeout for additional safety.
Supports daisy-chaining the qik to other qiks and Pololu serial motor and servo controllers, allowing the control of up to hundreds of motors and servos with a single serial line.
Comprehensive users guide.

Specifications:

Motor channels:	2
Motor supply voltage:	4.5 to 13.5 V
Continuous output current per channel:	1 A
Peak output current per channel:	3 A
Auto-detect baud rate range:	1200 to 38400 bps
Fixed baud rate:	38400 bps
Available PWM frequencies:	31.5 kHz, 15.7 kHz, 7.8 kHz, 3.9 kHz
Logic supply voltage:	2.7 to 5.5 V
Logic supply current:	< 15 mA
Reverse voltage protection?:	Y (on motor supply only)
Motor driver:	TB6612FNG

Installation:

The qik ships with a 161 straight 0.100" male header strip, a 121 right angle 0.100" male header strip, and two red shorting blocks. This hardware offers several options when it comes to making connections to the qik.

For the most compact installation, wires can be directly soldered to the qik pins themselves. For less permanent connections, the 161 straight header strip can be broken into a 121 piece and two 21 pieces. The 21 pieces can optionally be soldered into the jumper pins, and the 121 header strip of your choice can be soldered into the qik control pins. This allows connections to the qik via custom-made cables that have female headers on them, or the qik can simply be plugged into a breadboard. Using the right angle header allows for a compact profile or for vertical mounting into a breadboard; using the straight header allows for breadboarding as shown in the picture above.

Documents:

Price: $29.95

ATO-110 GW51C-MAXI-WDT RS-232/RS-422/RS-485 10/100 Mb Ethernet Serial Server

Wed, 14 Mar 2012 13:48:05 +1100

The Industrial Serial Server GW51C-MAXI-WDT is a cost effective gateway for Ethernet (TCP/IP) and serial signal communications. It allows almost any serial device to be connected to a new or existing Ethernet network.

By encapsulating serial data and transporting it over Ethernet, GW51C-MAXI-WDT offers full-duplex and bi-directional data that is transmission transparent between the serial port and the Ethernet network.

Flexible configuration options enable this unit to be setup over Ethernet by Telnet, Web browser, Serial Console, or a downloadable Windows utility. Packed in a rugged metal housing for DIN-Rail mount with a 9 to 30 VDC wide power input range, the GW51C-MAXI-WDT is ideal for almost any industrial and manufacturing automation.

In industrial and manufacturing automation fields, GW51C-MAXI-WDT is used as a field device to connect the Ethernet through TCP/IP protocol directly. It is also specially designed for conjunction with PLCs, HMIs, Barcode Scanners, Data Terminals, Electronic Kanbans, Shop Floor Control Systems, and Pick-to-Light Systems.

Specifications:

Ethernet
Compliance:	IEEE802.3
Port:	1-port
Transmission Rate:	10/100Mbps Auto-detection
Connector:	RJ-45
Auto MDI/MDI-X:	Yes

Link Mode
TCP Server:	Single connection or Virtual Com mode
TCP Client:	Single destination or Virtual Com mode
UDP:	Up to 4 Ranges of IPs

Serial
Interface:	RS-232/422/485 software selectable
Ports:	1-port
Baud Rate:	1200bps to 230 kbps
Parity:	None, Odd, Even, Mark, Space
Data Bits:	7, 8
Stop Bits:	1, 2
Flow Control:	None, Software: Xon/Xoff, Hardware: RTS/CTS
Protection:	15 kV ESD
Connector:	5-pin 5.08mm terminal block / 8-pin Mini DIN

Power
Input:	9 to 30 VDC
Consumption:	≤2.8 W

Approval
EMC:	FCC Class A, CE Class A

Environment
Operating	0C to 60C ( 32 to 140F )
Storage:	-40 to 85C ( -40 to 185F ), 5 to 95%RH

Dimension
W x H x D:	45 x 91 x 80mm

Software
Configuration:	Web Page / Telnet / Serial console / Windows utility
Virtual Com:	Windows and Linux port redirection software
Support Protocol:	ICMP, TCP(UDP) / IP, DHCP client, SNMP, HTTP

Documents:

Price: $199.00

ATO-105 SE5002 2 Port RS-232/RS-422/RS-485 10/100 Mb Ethernet Serial Server

Wed, 14 Mar 2012 11:36:44 +1100

The Industrial Serial Server SE5002 is a cost effective 2 port gateway for Ethernet (TCP/IP) and serial signal communications. It allows almost any serial device to be connected to a new or existing Ethernet network.

By encapsulating serial data and transporting it over Ethernet, SE5002 offers full-duplex and bi-directional data that is transmission transparent between the serial port and the Ethernet network.

Flexible configuration options enable this unit to be setup over Ethernet by Telnet, Web browser, Serial Console, or a downloadable Windows utility. Packed in a rugged metal housing for wall or DIN-Rail mount with 5 VDC or 9 to 30 VDC wide power input range, SE5002 is ideal for almost any industrial and manufacturing automation.

Specifications:

Ethernet
Compliance:	IEEE802.3
Transmission Rate:	10/100Mbps Auto-detection
Connector:	RJ-45
Auto MDI/MDI-X:	Yes

Link Mode
TCP Server:	Single connection or Virtual Com mode
TCP Client:	Single destination or Virtual Com mode
UDP:	Up to 4 Ranges of IPs

Serial
Interface:	RS-232/422/485 software selectable
Ports:	2 independent serial ports
Baud Rate:	1200 bps to 230 kbps
Parity:	None, Odd, Even, Mark, Space
Data Bits:	7, 8
Stop Bits:	1, 2
Flow Control:	None, Software: Xon/Xoff, Hardware: RTS/CTS
Protection:	15 kV ESD
Connector:	5 pin, 3.81 mm terminal block

Power
Input:	5 VDC or 9 to 30 VDC
Consumption:	≤1.5 W

Approval
EMC:	FCC Class A, CE Class A

Environment
Operating	0 to 60 C (32 to 140 F)
Storage:	-40 to 85 C (-40 to 185 F), 5 to 95% RH

Dimension
W × H × D:	65 × 78 × 28 mm

Software
Configuration:	Web Page / Telnet / Serial console / Windows utility
Virtual Com:	Windows and Linux port redirection software
Support Protocol:	ICMP, TCP(UDP) / IP, DHCP client, SNMP, HTTP

Documents:

Price: $189.00

CET-039 Replacement NTC Thermistor

Tue, 06 Mar 2012 11:02:21 +1100

Replacement NTC Thermistor for Novus N320, N321, N322 and N323 electronic thermostats. 3metre long and waterproof
Price: $11.95

HER-224 HB2-EW3161 Flange Indicator Pushbutton 1NO Blue

Tue, 06 Mar 2012 10:50:45 +1100

Industrial pushbutton with a flange that prevents activation of the button except by pressing directly against the face. Suits a ⌀22 mm hole (like those in our 1, 2, 3 and 4 button enclosures.)

Comes with a 24 V LED indicator.

The HB2/XB2 series pushbuttons have interchangeable contact modules. This pushbutton comes with a set of normally open contacts rated to 10 A and 400 VAC

Features:

Flange to prevent acidental activation
Suits standard ⌀22 mm holes
LED indicator
1NO: Single set of normally open contacts

Specifications:

Contact Resistance:	≤50 mΩ
Dielectric Strength:	2.5 kVAC / 1 min
Contact Life:	50 10⁴ operations
Protection Rating:	IP40
Rated Insulation Voltage:	660 V
Rated Current:	10 A
Rated Operational Voltage:	400 VAC
Indicator Voltage:	24 VAC/DC
Operational Temperature Range:	-5 to 40 C
Operational Humidity Range:	45 to 85%

Dimensions:

Price: $11.95

RHT-033 Replacement Temperature Sensor

Tue, 06 Mar 2012 10:43:43 +1100

p>Replacement Temperature and Humidity Sensor for Temp-WM (Wall Mount) and Temp-DM (Duct Mount) Transmitters.

Price: $39.00

CET-113 N323-RHT-485 Temperature & RH Controller w/ RS-485, 240VAC

Sat, 25 Feb 2012 12:37:06 +1100

The N323RHT is a digital controller for relative humidity and temperature. Its 3 relay outputs can be configured independently as control or alarm, either for temperature or relative humidity. A Relative Humidity and Temperature or RHT probe (3 m length) is provided along with the instrument

The temperature, humidity and status of relays are shown on the LED Display.

Each relay output has configurable set point, hysteresis and action. Relays can trigger above or below setpoints, within or outside temperature ranges. On and off times are configurable.

Relay outputs can drive fans, compressors, pumps, heaters etc. to control the temperature and humidity.

The controller has an RS-485 port and communicates via Modbus RTU, allowing integration into building management or logging systems.

Applications include fruit storage and air conditioning.

Features:

RHT sensor probe with 3 metre cable included
Tripple independent relay output
Bright, 3.5 digit LED display
Adjustable hystereses and configurable setpoint minimum and maximum limits
Configurable password protection
IP65 when installed in a panel
Third output can be set as a cyclic timer
RS-485 Modbus communications

Specifications:

Sensor Probe:
Humidity measurement accuracy:	3% from 20% to 80%
Humidity stability:	≤1 %RH / year
Humidity measurement range:	0 to 100 % RH
Humidity linearity error:	≤1 % RH
Long term humidity stability:	≤1 % RH
Humidity response time:	4 seconds (10 to 90 %)
Temperature measurement accuracy:	0.5 to 2 °C depending on temperature
Temperature repeatability:	0.1 C
Temperature measurement range:	-20 to 100 C
Cable length:	3 metres

Controller:
Warm-up:	15 minutes
Temperature resolution:	0.1 (19.9 and 119.9)
RH resolution:	1%
OUTPUT1 Relay:	SPDT, 16A / 250 VAC (1 HP)
OUTPUT2 Relay:	SPST, 3A / 250 VAC
OUTPUT3 Relay:	SPST, 5A / 250 VAC
Power:	100 to 240 VAC ( 10 %)
Mains frequency:	50 to 60 Hz
Power consumption:	5 VA
Serial Port:	RS-485
Communication:	Modbus RTU protocol

Physical and Environmental:
Dimensions:	75 × 33 × 75 mm
Panel cut-out:	70 × 29 mm
Weight:	120 g
Operating temperature:	0 to 40 C
Storage temperature:	-20 to 60 C
Operating relative humidity:	20 to 85 % non condensing
Case:	Polycarbonate UL94 V-2
Ingress protection (front):	IP65
Ingress protection (rear):	IP42
Suitable wiring:	Up to 4.0 mm

Documents:

Download info on probe covers

Price: $209.00

CET-112 N323-RHT-485-24V Temperature & RH Controller w/ RS-485, 24V

Fri, 24 Feb 2012 16:54:57 +1100

The N322RHT is a digital controller for relative humidity and temperature. Its 2 relay outputs can be configured independently as control or alarm, either for temperature or relative humidity. A Relative Humidity and Temperature or RHT probe (3 m length) is provided along with the instrument

The temperature, humidity and status of relays are shown on the LED Display.

Each relay output has configurable set point, hysteresis and action. Relays can trigger above or below setpoints, within or outside temperature ranges. On and off times are configurable.

Relay outputs can drive fans, compressors, pumps, heaters etc. to control the temperature and humidity.

The controller has an RS-485 port and communicates via Modbus RTU, allowing integration into building management or logging systems.

Applications include fruit storage, data centres and air conditioning.

Features:

RHT sensor probe with 3 metre cable included
Dual independent relay output
Bright, 3.5 digit LED display
Adjustable hystereses and configurable setpoint minimum and maximum limits
Configurable password protection
IP65 when installed in a panel
RS-485 Modbus communications

Specifications:

Sensor Probe:
Humidity measurement accuracy:	3% from 20% to 80%
Humidity stability:	≤1 %RH / year
Humidity measurement range:	0 to 100 % RH
Humidity linearity error:	≤1 % RH
Long term humidity stability:	≤1 % RH
Humidity response time:	4 seconds (10 to 90 %)
Temperature measurement accuracy:	0.5 to 2 °C depending on temperature
Temperature repeatability:	0.1 C
Temperature measurement range:	-20 to 100 C
Cable length:	3 metres

Controller:
Warm-up:	15 minutes
Temperature resolution:	0.1 (19.9 and 119.9)
RH resolution:	1%
OUTPUT1 Relay:	SPDT, 16A / 250 VAC (1 HP)
OUTPUT2 Relay:	SPST, 3A / 250 VAC
OUTPUT3 Relay:	SPST, 5A / 250 VAC
Power:	12 to 30 VAC/DC
Power consumption:	5 VA
Serial Port:	RS-485
Communication:	Modbus RTU protocol

Physical and Environmental:
Dimensions:	74 × 32 × 75 mm
Panel cut-out:	70 × 29 mm
Weight:	100 g
Operating temperature:	0 to 40 C
Storage temperature:	-20 to 60 C
Operating relative humidity:	20 to 85 % non condensing
Case:	Polycarbonate UL94 V-2
Ingress protection (front):	IP65
Ingress protection (rear):	IP42
Suitable wiring:	Up to 4.0 mm

Documents:

Download info on probe covers

Price: $209.00

KTA-250-BX 24V Anemometer Interface

Fri, 24 Feb 2012 16:16:21 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $179.00

KTA-250-AX 12V Anemometer Interface

Fri, 24 Feb 2012 14:17:45 +1100

Features:

Connects to Davis Instruments DS7911 Anemometer
Monitor both the wind speed and direction
Interface to PLCs using the Modbus protocol
Communicate via USB or 2-wire RS485
Interface to PLCs/Instruments or other controllers using 4-20mA or 0-5V signals
Generate relay alarms depending on the wind speed and direction
Alarms can be monitored by the on board relays or via the Modbus protocol
DIN Rail or wall/panel mount

Selection:

All with DIN Rail mountable enclosure.

KTA-250-AX - 12V Powered, No Logging, No LCD
KTA-250-BX - 24V Powered, No Logging, No LCD
KTA-250-AL - 12V Powered, 64k Logging, No LCD
KTA-250-BL - 24V Powered, 64k Logging, No LCD
KTL-250-AX - 12V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-BX - 24V Powered, No Logging, With White on Blue Backlit LCD
KTL-250-AL - 12V Powered, 64k Logging, With White on Blue Backlit LCD
KTL-250-BL - 24V Powered, 64k Logging, With White on Blue Backlit LCD

Software:

Downloads:

Price: $179.00

KTD-273 Solid State Relay Terminal Card DIN Rail Mount

Fri, 24 Feb 2012 10:58:18 +1100

The KTD-273 is a single Solid State Relay (SSR-001) mounted on DIN rail clips for quick and easy use in any application.

Load Current: 2A.
Load Voltage 24 to 400 VAC
3 to 24 VDC input control.
Control current: 6 to 25 mA.
Zero crossing, over load protected.
Optical isolation between input and output terminals.

Also available without DIN rail mount: KTA-273

Price: $19.00

KTA-273 Solid State Relay Terminal Card

Fri, 24 Feb 2012 10:42:33 +1100

The KTA-273 is a single Solid State Relay (SSR-001) mounted on terminal card for quick and easy use in any application.

Load Current: 2A.
Load Voltage 24 to 400 VAC
3 to 24 VDC input control.
Control current: 6 to 25 mA.
Zero crossing, over load protected.
Optical isolation between input and output terminals.

Also available with DIN rail mount: KTD-273

Price: $15.00

ATO-161 MB5001C 1-port Modbus/ModbusTCP Gateway

Fri, 24 Feb 2012 10:15:35 +1100

The Atop MB5001C series provides an interface between Modbus serial slave devices and hosts running Modbus/TCP on Ethernet networks. This low power, compact device is housed in a metal casing making them ideal for interfacing industrial equipment such as PLCs, HMIs, various sensors and measuring instruments. User friendly setup via a web based UI ensures simple integration even for complex configurations.

The MB5001C series supports the three most commonly used serial communication interfaces, RS-232, RS-422 and RS-485. It also provides a web-based configuration UI, so the users can select the serial interface easily.

Features:

Rugged metal housing for wall or panel mount (DIN rail adapter clips available)
Ease-of-use in Modbus protocol conversion include RTU, ASCII and TCP
10/100 Mbps fast Ethernet full duplex auto negotiation
Monitor, manage and control industrial field devices remotely
Configurable via built-in web server, serial console, and telnet
Upgradeable firmware from remote-PC via Ethernet
Compact design

Specifications:

Ethernet
Compliance	IEEE802.3
Port	1-port
Transmission Rate	10/100M Auto-detection
Connector	RJ-45
Auto MDI/MDI-X	Yes

Link Mode
Modbus TCP	Yes
Modbus ASC	Yes
Modbus RTU	Yes

Serial
Interface	RS-232/422/485 software selectable
Ports	1-port
Baud Rate	1200 bps to 230 Kbps
Parity	None, Odd, Even, Mark, Space
Data Bits	7, 8
Stop Bits	1, 2
Flow Control	None, Software: Xon/Xoff, Hardware: RTS/CTS
Protection	15 kV ESD
Connector	9-pin D-Sub

Power
Input	5 VDC (DC-Jack) or 9 to 30 VDC (screw terminals)
Consumption	≤2.7 W

Approval
EMC	FCC Class A, CE Class A

Environment
Operating	0 to 60 C
Storage	-20 to 70 C, 5 to 95% RH

Dimension
W × H × D	65 × 28 × 78 mm

MTBF
Preceding	57.5 years (25 °C)
Report	Yes

Software
Configuration	Web Page / Telnet / Serial console / Windows utility
Atop Tool	DeviceView
Support Protocol	Modbus TCP/ASC/RTU, SNMP, HTTP

Resources:

Download Quick Start Guide
Download User Manual

DOwnload DeviceView 1.12 configuration utility for Windows
ATOP Product page with firmware, software and manuals

Price: $189.00

CET-109 N322-RHT Temperature and RH Controller 240VAC

Tue, 21 Feb 2012 14:02:14 +1100

The temperature, humidity and status of relays are shown on the LED Display.

Each relay output has configurable set point, hysteresis and action. Relays can trigger above or below setpoints, within or outside temperature ranges. On and off times are configurable.

Relay outputs can drive fans, compressors, pumps, heaters etc. to control the temperature and humidity.

Applications include fruit storage and air conditioning.

Features:

RHT sensor probe with 3 metre cable included
Dual independent relay output
Bright, 3.5 digit LED display
Adjustable hystereses and configurable setpoint minimum and maximum limits
Configurable password protection
IP65 when installed in a panel

Specifications:

Sensor Probe:
Humidity measurement accuracy:	3% from 20% to 80%
Humidity stability:	≤1 %RH / year
Humidity measurement range:	0 to 100 % RH
Humidity linearity error:	≤1 % RH
Long term humidity stability:	≤1 % RH
Humidity response time:	4 seconds (10 to 90 %)
Temperature measurement accuracy:	0.5 to 2 °C depending on temperature
Temperature repeatability:	0.1 C
Temperature measurement range:	-40 to 120 C
Temperature response time:	≤30 seconds
Temperature measurement range:	-40 to 120 C
Cable length:	3 metres

Controller:
Warm-up:	15 minutes
Temperature resolution:	0.1 (19.9 and 119.9)
RH resolution:	1%
OUTPUT1 Relay:	SPDT, 1 HP 250 VAC / 1/3 HP 125 VAC (10 A Resistive)
OUTPUT2 Relay:	SPST, 3A / 250 VAC
Power:	100 to 240 VAC ( 10 %)
Mains frequency:	50 to 60 Hz
Power consumption:	5 VA

Physical and Environmental:
Dimensions:	74 × 32 × 75 mm
Panel cut-out:	70 × 29 mm
Weight:	100 g
Operating temperature:	0 to 40 C
Storage temperature:	-20 to 60 C
Operating relative humidity:	20 to 85 % non condensing
Case:	Polycarbonate UL94 V-2
Ingress protection (front):	IP65
Ingress protection (rear):	IP42
Suitable wiring:	Up to 4.0 mm

Documents:

Price: $195.00

SFS-300 VCNL4000 Infrared Emitter Breakout

Mon, 20 Feb 2012 15:30:52 +1100

In physical computing it's sometimes nice to know how physically close you are to an object. In other words, you may need to know your 'proximity' to an object, that's where the VCNL4000 does its magic. Okay, it's not actually magic, it's a combination ambient light sensor and IR proximity sensor.

The VCNL4000 can detect its proximity to an object using IR within a range of about 20cm. Proximity data as well as ambient light level data can be collected over an I2C interface. This breakout board gives you access to the I2C pins, the Vcc pin, GND and the IR+ pin (power supply for the built-in IR emitter). Simply give the board a clean 3.3V power source and give the IR emitter anywhere from 2.5 to 5V and you'll be able to tell how far you are from an object up to 20cm.

Features:

Voltage Rating: 3.3V
IR Emitter Vin: 2.5-5V
I/O pins are 5V compliant
Range: Up to 20cm
Built-in Ambient Light Sensor

Documents:

Price: $9.95

SFA-104 Arduino Mega 2560 R3

Mon, 20 Feb 2012 15:01:06 +1100

Arduino is an open-source physical computing platform based on a simple I/O board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux).

The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.

The Mega 2560 R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Mega 2560 R3 works with all existing shields but can adapt to new shields which use these additional pins.

Features:

ATmega2560 microcontroller
Input voltage: 7 to 12 VDC
54 Digital I/O Pins (14 PWM outputs)
16 Analog Inputs
256k Flash Memory
16Mhz Clock Speed

Documents:

Price: $59.00

ATO-101 SE5001 RS-232/RS-422/RS-485 10/100 Mb Ethernet Serial Server

Sun, 19 Feb 2012 16:21:23 +1100

The Industrial Serial Server SE5001 is a cost effective gateway for Ethernet (TCP/IP) and serial signal communications. It allows almost any serial device to be connected to a new or existing Ethernet network.

By encapsulating serial data and transporting it over Ethernet, SE5001 offers full-duplex and bi-directional data that is transmission transparent between the serial port and the Ethernet network.

Flexible configuration options enable this unit to be setup over Ethernet by Telnet, Web browser, Serial Console, or a downloadable Windows utility. Packed in a rugged metal housing for wall or DIN-Rail mount with 5 VDC or 9 to 30 VDC wide power input range, SE5001 is ideal for almost any industrial and manufacturing automation.

In industrial and manufacturing automation fields, SE5001 is used as a field device to connect the Ethernet through TCP/IP protocol directly. It is also specially designed for conjunction with PLCs, HMIs, Barcode Scanners, Data Terminals, Electronic Kanbans, Shop Floor Control Systems, and Pick-to-Light Systems.

Specifications:

Ethernet
Compliance:	IEEE802.3
Port:	1-port
Transmission Rate:	10/100Mbps Auto-detection
Connector:	RJ-45
Auto MDI/MDI-X:	Yes

Link Mode
TCP Server:	Single connection or Virtual Com mode
TCP Client:	Single destination or Virtual Com mode
UDP:	Up to 4 Ranges of IPs

Serial
Interface:	RS-232/422/485 software selectable
Ports:	1-port
Baud Rate:	1200bps to 230 kbps
Parity:	None, Odd, Even, Mark, Space
Data Bits:	7, 8
Stop Bits:	1, 2
Flow Control:	None, Software: Xon/Xoff, Hardware: RTS/CTS
Protection:	15 kV ESD
Connector:	5 pin, 3.81 mm terminal block

Power
Input:	5 VDC or 9 to 30 VDC
Consumption:	≤1.5 W

Approval
EMC:	FCC Class A, CE Class A

Environment
Operating	0C to 60C ( 32 to 140F )
Storage:	-40 to 85C ( -40 to 185F ), 5 to 95%RH

Dimension
W x H x D:	65 x 78 x 28mm

Software
Configuration:	Web Page / Telnet / Serial console / Windows utility
Virtual Com:	Windows and Linux port redirection software
Support Protocol:	ICMP, TCP(UDP) / IP, DHCP client, SNMP, HTTP

Documents:

Price: $129.00

ATO-005 EH2308 Unmanaged 8 port Ethernet switch

Sun, 19 Feb 2012 05:23:23 +1100

The EH2308 is an Industrial Ethernet Switch with 8 10/100BaseT(X) ports that provides a reliable and economical solution for your industrial Ethernet connections.

The EH2308 protects itself from receiving too many broadcast packets. During normal use, broadcast packets will be forwarded to all ports except the source port. However, it will discard broadcast or multicast packets if the number of those packets exceeds a threshold in a preset period of time. When the preset period expires (about 800ms), it will then resume receiving broadcast or multicast packets until the threshold is reached again.

EH2308 provides two redundant power inputs that can be connected simultaneously to wide-range DC power sources. If one of the power inputs failure, the other live source acts as a backup to provide the EH2308 power needs automatically.

5 Year Warranty

Specifications:

Technology
Standards	IEEE802.3, 802.3u, 802.3x
Processing Type	Store and Forward
Flow Control	IEEE802.3x flow control, backpressure flow control

Interface
RJ-45 Ports	10/100BaseT(X) auto negotiation speed Full/Half-duplex mode, and auto MDI/MDI-X connection
LED Indicators	Power, 10/100M

Power
Input	DC 9~48V
Connector	5-pin 5.08mm pitch terminal block
Consumption	4 Watts Max.
Reverse Polarity Protection	Present

Physical
Housing	IP50 protection, metal housing
Dimension	45.2 × 90 × 78 mm (W × H × D)
Weight	255 g

Approval
UL(Safety)	UL60950-1 2nd Ed. /CSA C22.2 No.60950-1-07 2nd Ed
FCC(EMI)	FCC 47 CFR Part15, Subpart B, Class A
CE(EMI)	European Standard EN 55022:2006/A1:2007 Class A EN 61000-3-2:2006 EN 61000-3-3: 1995/A1:2001/A2 :2005
CE(EMS)	EN 55024:1998/A1:2001/A2:2003 (IEC 61000-4-2:1995/A2:2000) IEC 61000-4-3:2002 IEC 61000-4-4:2004 IEC 61000-4-5:1995/A1:2000 IEC 61000-4-6:1996/A1:2000 IEC 61000-4-8:1993/A1:2000 IEC 61000-4-11:1994/A1:2000
Shock	IEC 60068-2-27
Drop	ISTA Test Procedure 2A
Vibration	IEC 60068-2-64
RoHS	Lead(Pb) Free
MTBF	568862 hrs(25C) / 64.94 years(25C)
Warranty	5 years

Environment
Operating	-10 ~ 70C
Storage	-40 ~ 85C ( -40~ 185F )
Ambient Relative Humidity	5%~95% non-condensing

Documents:

Download Datasheet

Price: $159.00

NOW-001 AirGate Modbus (Gateway RS485/Wireless)

Sat, 18 Feb 2012 09:41:18 +1100

AirGate-Modbus is a wireless multifunctional gateway that allows the transparent and easy insertion of wireless branches into existing wired RS-485 networks. The AirGate-Modbus has four operation modes, Modbus Master, multiplexer, USB-RS-485 converter and simple wireless RS-485 extension. A proprietary protocol based on IEEE 802.15.4 facilitates operation in Star mode, allowing the connection of several wireless segments to an existing Modbus RS-485 network.

Features:

Operating Band ISM 2.4 GHz
Star network topology operation
Up to 16 operating channels
Maximum transmission power up to 100 mW
Indoor range up to 100 m and 1000 m outdoors
RF data rate up to 250 Kbps
Network identifier (PAN ID)
AES-CBC-128 Data cryptography (Advanced Encryption Standard)
Serial port Baud Rate 1200 to 115.2 Kbps
Power Supply 10 to 35 Vdc
Power consumption 70 mA (@ 24 Vdc)
Operating Temperature 0 to 70 C
Allows 4 operating modes: RS485-Master, RS485-Slave, USB-Master and Multi-Master
RP SMA female connector (Plug)
Antenna gain 2 dBi
Two RS485 connector for Modbus RTU interface
USB Device (Mini-B)
Status indication LEDs

Specifications

Communication characteristics:
Maximum transmission power:	100 mW
Range:	1000 metres LOS (100 m typical indoor)
Over-the-air datarate:	250 kbps
Serial baudrate:	1200 bps to 115.2 kbps
RF Receive Sensitivity:	-92 dBm

Network and Security:
RF Band:	ISM 2.4 GHz
Frequency and Modulation:	DSSS OQPSK
RF Band:	ISM 2.4 GHz
Frequency and Modulation:	DSSS OQPSK
Network topology:	Star
Channels:	16
Network identifier:	PAN ID
Encryption:	AES-CBC-128

Connections:
Power:	Screw terminals
USB:	USB client Mini-B
Antenna:	Reverse SMA female
Serial:	RS-485 screw terminals

Power:
Voltage:	10 to 35 VDC
Consumption:	70 mA at 24 V

Environmental:
Temperature:	0 to 70 °C
Relative Humidity:	≤80%
EMC:	EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, CISPR11
Weight:	110 g
Housing:	ABS+PC, DIN rail mount
Dimensions:	99.5 × 114 × 17.5 mm
Ingress Protection:	IP20

Documents:

Price: $489.95

MET-111 Clamp Meter AC/DC True RMS 600A

Wed, 15 Feb 2012 10:45:05 +1100

This rugged & versatile autoranging digital clamp meter quickly and accurately measures the current flowing through an individual conductor. Simply clamp the jaws around the conductor and the display reads the DC or AC current present, up to a massive 600A. Activating the Peak Hold button will display the highest current reading obtained during the test. Features a one touch zero adjustment for DC current measurement and Data Hold function to freeze the display while measuring. It also features autoranging AC/DC volts and current, resistance, temperature, capacitance ranges plus a diode and continuity test function. An essential piece of test gear for high voltage technicians, instrument fitters and other electrical tradespeople. Supplied with high quality test leads, temperature probe, and carry case.

Features:

Autoranging Up to 600A AC or DC current
True RMS AC measurement
One touch zero function 33mm jaw opening
Auto power off Peak hold function
High quality test leads
Temperature probe
Carry case
Battery included

Specifications:

DC voltage:	400mV, 4V, 40V, 400V, 600V
AC voltage:	4V, 40V, 400V, 600V
DC & AC current:	600A
Resistance:	to 40 MΩ
Continuity:	50Ω threshold, audible tone
Diode test:	Test current 1mA max
Temperature:	-20C to 760C
Capacitance:	40nF to 100F
Display:	3.5 digit, 1999 count, backlit
Dimensions:	80 × 43 × 204 mm

Price: $108.18

SEC-005 Key Fob RFID Tag

Mon, 06 Feb 2012 16:42:25 +1100

Key Fob with RFID Tag

Features:

64 bit code
Resonance Frequency 125 kHz
Operating Temperature: -15 ~ 55 deg. C

Price: $9.15

DEC-200 DVP PLC RS232 Serial Programming Cable

Sat, 04 Feb 2012 16:46:15 +1100

DVPACAB2A30 DVP Series PLC RS232 Serial Programming Cable. Use it between a serial port on your PC to program a DVP series PLC
Price: $25.00

DEI-100 DOP Series HMI USB Programming Cable

Sat, 04 Feb 2012 16:30:46 +1100

Delta DOP Series USB programming upload/download cable

Price: $14.95

DEI-101 DOP HMI to Delta PLC Communication Cable

Sat, 04 Feb 2012 16:14:27 +1100

p>RS-232 serial cable with the correct plugs and pinout to connect a Delta Electronics HMI (DOP-B series touchscreen HMIs) to a Delta Electronics PLC. Connects to the first serial port of the HMI.

Price: $14.95

DEI-050 Delta DOP-B10E615 10" High Resolution 16:9 Touchscreen HMI

Sat, 04 Feb 2012 10:45:55 +1100

The DOP-B10E615 from Delta Electronics is a 10" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

The screen is a widescreen (16:9), LED-backlit touchscreen with a high resolution and colour depth allowing realistic images and detailed displays. The 128 MB flash memory gives you plenty of space for screens full of images.

3 serial ports and 10/100 Mb ethernet allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

Programming is performed over serial, USB or high-speed ethernet using the free ScreenEditor software for Windows. HMI projects can be compiled and downloaded to USB key or SD card for loading onto the HMI out in the field. The HMI can act as a bridge allowing programming of a connected Delta Electronics PLC.

The USB and SD card features of the HMI allow expanded logging, data export and connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

Features:

High resolution (1024 × 600), 65536 colour widescreen touchscreen
LED backlit screen for low power consumption
3 serial ports, USB and ethernet
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
SD card slot
Built-in RTC
Built-in buzzer and stereo output jack
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	10" 16:9 TFT LCD
Resolution:	800 × 600
Backlight:	LED (≥10,000 hour half-life)
Flash ROM:	128 MB
SDRAM:	64 MB
Sound Output:	Internal 2 to 4 kHz buzzer, stereo output jack
Ethernet:	10/100 Mbps Auto sensing
Memory Card:	SD Card slot supporting SDHC
USB Client:	USB ver 2.0, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	12 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	272 × 200 × 61 mm
Panel Cutout:	262.3 × 189.3 mm
Weight:	1520 g

Downloads:

Price: $1299.00

DEI-040 Delta DOP-B08E515 8" High Resolution 4:3 Touchscreen HMI

Sat, 04 Feb 2012 10:37:52 +1100

The DOP-B08E515 from Delta Electronics is a 8" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

The screen is a standard ratio (4:3), LED-backlit touchscreen with a high resolution and colour depth allowing realistic images and detailed displays. The 128 MB flash memory gives you plenty of space for screens full of images.

3 serial ports and 10/100 Mb ethernet allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

The USB and SD card features of the HMI allow expanded logging, data export and connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

Features:

High resolution (800 × 600), 65536 colour widescreen touchscreen
LED backlit screen for low power consumption
3 serial ports, USB and ethernet
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
SD card slot
Built-in RTC
Built-in buzzer and stereo output jack
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	8" 4:3 TFT LCD
Resolution:	800 × 600
Backlight:	LED (≥10,000 hour half-life)
Flash ROM:	128 MB
SDRAM:	64 MB
Sound Output:	Internal 2 to 4 kHz buzzer, stereo output jack
Ethernet:	10/100 Mbps Auto sensing
Memory Card:	SD Card slot supporting SDHC
USB Client:	USB ver 2.0, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	7.8 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	227.1 × 174.1 × 60 mm
Panel Cutout:	219.4 × 166.5 mm
Weight:	1228 g

Downloads:

Price: $1049.00

DEI-035 Delta DOP-B07E515 7" High Resolution 4:3 Touchscreen HMI

Sat, 04 Feb 2012 10:23:37 +1100

The DOP-B07E515 from Delta Electronics is a 7" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

3 serial ports and 10/100 Mb ethernet allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

The USB and SD card features of the HMI allow expanded logging, data export and connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

Features:

High resolution (800 × 600), 65536 colour widescreen touchscreen
LED backlit screen for low power consumption
3 serial ports, USB and ethernet
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
SD card slot
Built-in RTC
Built-in buzzer and stereo output jack
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	7" 4:3 TFT LCD
Resolution:	800 × 600
Backlight:	LED (≥20,000 hour half-life)
Flash ROM:	128 MB
SDRAM:	64 MB
Sound Output:	Internal 2 to 4 kHz buzzer, stereo output jack
Ethernet:	10/100 Mbps Auto sensing
Memory Card:	SD Card slot supporting SDHC
USB Client:	USB ver 2.0, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	7.68 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	184 × 144 × 50 mm
Panel Cutout:	172.4 × 132.4 mm
Weight:	800 g

Downloads:

Price: $799.00

DEI-033 DOP-B07E415 7" High Resolution 16:9 Touchscreen HMI

Sat, 04 Feb 2012 10:01:38 +1100

The DOP-B07E415 from Delta Electronics is a 7" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

3 serial ports and 10/100 Mb ethernet allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

The USB and SD card features of the HMI allow expanded logging, data export and connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

Features:

High resolution (800 × 480), 65536 colour widescreen touchscreen
LED backlit screen for low power consumption
3 serial ports, USB and ethernet
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
SD card slot
Built-in RTC
Built-in buzzer and stereo output jack
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	7" 16:9 TFT LCD
Resolution:	800 × 480
Backlight:	LED (≥20,000 hour half-life)
Flash ROM:	128 MB
SDRAM:	64 MB
Sound Output:	Internal 2 to 4 kHz buzzer, stereo output jack
Ethernet:	10/100 Mbps Auto sensing
Memory Card:	SD Card slot supporting SDHC
USB Client:	USB ver 2.0, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	7.5 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	215 × 161 × 50 mm
Panel Cutout:	196.9 × 142.9 mm
Weight:	970 g

Downloads:

Price: $799.00

DEI-030 DOP-B07S415 7" High Resolution 16:9 Touchscreen HMI

Sat, 04 Feb 2012 09:49:42 +1100

The DOP-B07S415 from Delta Electronics is a 7" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

3 serial ports allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

Programming is performed over serial, or USB using the free ScreenEditor software for Windows. HMI projects can be compiled and downloaded to USB key or SD card for loading onto the HMI out in the field. The HMI can act as a bridge allowing programming of a connected Delta Electronics PLC.

The USB and SD card features of the HMI allow expanded logging, data export and connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

Features:

High resolution (800 × 480), 65536 colour widescreen touchscreen
LED backlit screen for low power consumption
3 serial ports USB Host and USB Client
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
SD card slot
Built-in RTC
Built-in buzzer
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	7" 16:9 TFT LCD
Resolution:	800 × 480
Backlight:	LED (≥20,000 hour half-life)
Flash ROM:	128 MB
SDRAM:	64 MB
Sound Output:	Internal 2 to 4 kHz buzzer
Memory Card:	SD Card slot supporting SDHC
USB Client:	USB ver 2.0, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	5 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	215 × 161 × 50 mm
Panel Cutout:	196.9 × 142.9 mm
Weight:	970 g

Downloads:

Price: $649.00

DEI-027 DOP-B07S211 7" 16:9 Touchscreen HMI

Sat, 04 Feb 2012 09:42:13 +1100

The DOP-B07S211 from Delta Electronics is a 7" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

The screen is a widescreen (16:9), LED-backlit touchscreen with a high colour depth allowing realistic images and detailed displays.

3 serial ports allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

Programming is performed over serial or USB using the free ScreenEditor software for Windows. HMI projects can be compiled and downloaded to USB key for loading onto the HMI out in the field. The HMI can act as a bridge allowing programming of a connected Delta Electronics PLC.

By plugging a USB key into the HMI allows expanded logging and data export. The USB host port allows connection of peripherals including keyboards, mice, barcode scanners and other input devices and printers.

The front panel has 8 flat membrane pushbuttons, four of which perform system functions and four of which can be configured to perform user functions.

Features:

65536 colour widescreen touchscreen
LED backlit screen for low power consumption
8 physical buttons
3 serial ports and USB
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
Built-in RTC
Built-in buzzer
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC over USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	7" 16:9 TFT LCD
Resolution:	480 × 234
Backlight:	LED (≥20,000 hour half-life)
Flash ROM:	4 MB
SDRAM:	16 MB
Sound Output:	Internal 2 to 4 kHz buzzer
USB Client:	USB ver 1.1, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	4.8 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	215 × 161 × 50 mm
Panel Cutout:	196.9 × 142.9 mm
Weight:	840 g

Downloads:

Price: $649.00

DEI-025 DOP-B07S201 7" 16:9 Touchscreen HMI

Sat, 04 Feb 2012 09:23:00 +1100

The DOP-B07S201 from Delta Electronics is a 7" HMI touchscreen packed with features that easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

The screen is a widescreen (16:9), LED-backlit touchscreen with a high colour depth allowing realistic images and detailed displays.

3 serial ports allow connection to Delta Electronics and other brand PLCs, motor drives and generic Modbus devices.

The front panel has 8 rubberised pushbuttons, four of which perform system functions and four of which can be configured to perform user functions.

Features:

65536 colour widescreen touchscreen
LED backlit screen for low power consumption
8 physical buttons
3 serial ports and USB
USB host functions allow connection of a USB key, keyboard, mouse, barcode scanner or printer
Built-in RTC
Built-in buzzer
IP 65 for the display panel / NEMA4
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC over USB
Built to support MPI Siemens S7 PLC
ARM9 32-bit CPU

Specifications:

Display:	7" 16:9 TFT LCD
Resolution:	480 × 234
Backlight:	LED (≥20,000 hour half-life)
Flash ROM:	4 MB
SDRAM:	16 MB
Sound Output:	Internal 2 to 4 kHz buzzer
USB Client:	USB ver 1.1, Type B
USB Host:	USB ver 1.1, Type A
Serial Port 1:	DE-9, RS-232 with hardware flow control
Serial Port 2:	DE-9, RS-232 / RS-422 / RS-485
Serial Port 3:	DE-9, RS-232 / RS-422 / RS-485
Clock:	Battery-backed realt time clock
Cooling:	Natural air circulation
Safety Approvals:	CE, UL, KCC
Ingress Protection Rating:	IP65 / NEMA4 when installed
Operating Voltage:	24 VDC -10% +15%
Power Consumption:	4.8 W
Operating Temperature Range:	0 to 50 °C
Dimensions:	215 × 161 × 50 mm
Panel Cutout:	196.9 × 142.9 mm
Weight:	880 g

Downloads:

Price: $649.00

DEI-021 DOP-B05S100 5.6" Touchscreen HMI

Sat, 04 Feb 2012 04:20:12 +1100

The DOP-B05S100 from Delta Electronics is a great looking HMI touchscreen which easily interfaces to a number of different PLCs and protocols including Modbus. The Screen Editor software used to program the screen is free and easy to use.

Features include

Screen size: 5.6 inches
Resolution: 320 234 pixels
Display: TFT LCD, 65536 colors
LED Backlight: LED
Power supply: 24V DC
Processor ARM9 32-bit CPU
2MB flash memory
128KB SRAM
4 function keys
USB Host Interface 1.1 for USB flash drive, printer, mouse,
USB 1.1 port for programming desktop.
3 separate COM ports for multiple communication protocols: RS232 COM1, COM2 RS485/422, COM3 RS232
IP 65 for the display panel / NEMA4
Built-in RTC
Multilingual, recipes 16/32 bits, data collection, trends, alarms and more
USB Transparent mode for Delta PLC after USB
Built to support MPI Siemens S7 PLC
Free software: ScreenEditor Series 1

Download User Manual

Download HMI Screen Brochure

Download The ScreenEditor Software from the Delta Electronics website. (it is free!)

Price: $499.00

CMC-006 RT28U DIN Rail Mount On-Off Temp Controller with Universal Analog Input 12-24V

Thu, 02 Feb 2012 11:38:13 +1100

THe RT28U is a programmable thermostat controller with a universal analog input that accepts a wide range of sensor types and two independent relay outputs. Although primarily designed for temperature control it can be used for ON-OFF control of level, pressure etc

Sensor (not included):		Power:
PT100, PT1000		12-24VAC/DC
1 kΩ PTC, 2 kΩ PTC
0 to 1 kΩ linear resistance		Outputs:
0 to 100 mV linear voltage		2 x SPDT Relays
0 to 20 mA linear current		5 A, 250 VAC
4 to 20 mA linear current
0 to 10 V linear voltage		Display:
B, J, K, R, S, T thermocouples		3 Digit LED

Each relay has independent settings for setpoint, hysteresis, cooling or heating action and on time. Each output can be set to a pulse mode where the relay constantly toggles on and off when the temperature exceeds (or falls below) the setpoint.

The controller has peak filtering and low pass filtering options. The display or linear input signals can be scaled to any value between -199 and 999 with a configurable decimal point.

Dimensions: 110 70 60 mm.

Manufacturer part number: RTU28U-R1.P.CC

Features:

Universal analog input accepts a wide range of temperature sensors
Cold junction compensation for thermocouples, line compensation for RTDs
2 Relay outputs rated to 5 A, 250 VAC
≤0.3% full span measurement error
≤0.02%/C Temperature drift
2300 VAC powered
Heating or cooling actions
Configurable hysteresis and output delay and minimum times
24 VDC, 30 mA auxiliary supply to power sensors

Documents:

Download datasheet

Download the manual for a full product details

Download the wiring details

Price: $159.00