|
Function
The LonWorks Gateway communicates between LonWorks
network interface on one side and various serial protocols on
the other side (e.g. Modbus ASCII / RTU etc.). It allows
LonWorks devices to make available their
LonWorks variables for PLC’s or SCADA. It also
makes possible for a serial device to act as a
LonWorks node.
It is externally powered from a 3 pin terminal block and power is
isolated from both communication ports. Both the communication
ports are also isolated from each-other.
Microsoft Windows® based configuration software, Gateway
Setup, helps user to configure Gateway
unit. ‘Configuration’ means making the Gateway
unit work as per the system
requirements. The complete
configuration for a unit is termed as
‘Project’. Project comprises of device names, Register
addresses, Conditions for block execution etc.
Block may contain information like copy number of Words, Bits
etc. from one device to other device and conditions for copy, if
any. Gateway transfers data between two devices
by execution of blocks.
After the Project is defined, Drivers for
required devices and Project should be
downloaded. Gateway can now communicate
with the connected devices and transfers data between them.
A serial PC Programming Cable for the Gateway is
available. Do Not use a normal straight through cable.
Our LonWorks Gateway (GWY-100) supports LONMARK
Functional Profile for Variable Speed Motor Drives-6010
|
Purchase |
|
Features include
-
DIN
Rail or Panel Mounted compact Protocol Converter
- Hardware with two communication ports COM1: RS232 / RS422 / 2 or
4 wire RS485 / CMOS
- COM2: LonWorks TP FT10 (78 Kbps, free
topology)
- Connect your LonWorks device to serial
device or vice versa
- Connect your LonWorks device on Modbus
Network (as a Master / Slave)
- Same model can be re-configured for
connecting different devices
- Supports up to 62 network variables
- Free software for Gateway and SNVT
variables configuration!!
- CE with UL certification
- We welcome opportunity to develop new
/ customized drivers for UNVT templates
|
General
Specifications |
|
Power
|
12 V DC to 32 V DC, 1.6 W |
|
LED |
3 LED’s for status indication
and 1 LED for device
configuration status |
Communication Ports
|
2 Communication ports with
COM1 : RS232 / RS422 / RS485 / CMOS
COM2 : LonWorks Network Interface.
TP FT-10 (78 Kbps, free topology)
|
|
Isolation |
Isolation
between communication ports and Power supply,
through DC-DC coupler is 1 KV.
COM1 / PLC1 : Connects to PC for setup download
or connects to PLC1 at runtime.
COM2 / PLC2 : LonWorks Network Interface.
TP FT-10 (78 Kbps, free
topology)Isolation between communication ports,
through opto-isolation
is 1KV rms for 1 min. |
|
GSD File |
Supplied with the
unit (Included in Setup Software) |
|
I/O Data |
100 Word Input, 100
Word Output |
|
BUS Address |
0 - 255 Setting
through setup software |
|
Operating Temp. |
0º to
60º C |
|
Storage Temp. |
-20º to 80º C |
|
Humidity |
10% to 90% (Non
Condensing) |
|
Mounting |
DIN rail or back
panel mounting |
|
Dimensions |
105(L)
X 40(D) X
51(W) mm |
|
Weight |
125g Approximately. |
Download Information Sheet
PURCHASING THE LONWORKS GATEWAY
All prices are in Australian Dollars. Prices do not include GST (Goods and
Services Tax). 10% GST applies to goods delivered in Australia. Australian GST is not paid
on shipments despatched to an international destination. You can check the exchange rate
by going to http://www.x-rates.com
|
|
