ocontrol_surf6.jpg (3863 bytes)
Ocean Controls
PO Box 2191
Seaford BC
Factory 3/24Wise Ave

Seaford,
Vic, Australia 3198
ABN 22 061 932 027

Ph 61 3 9782 5882
Fax 61 3 9782 5517

Email Us


• Catalogue
• Shopping Cart
• Ordering Info
• Specials
• What's New
• Home
• Audio
• Communications
• Computer Products
• Controllers
• Counters Timers
• Data Acquisition
• Data Loggers
• Micro Programmers 
• Modbus Products
• Moscad RTU
• Motor Controllers
• Motors
• Panel Meters
• PLC's
• Power Supplies
• Relays
• Sensors
• Signal Conditioners
• Software Commercial
• 
Software Industrial
• Test Equipment


   
Relay Cards



2, 4, 6 or 8 Relay Card with wide voltage control. Available in 12VDC or 24VD
C

These would have to be the most versatile relay cards on the market. Each relay can be operated by TTL levels, NPN and PNP open collector or 0 to 12V(0 to 24V if using 24VDC relays). Each relay has two inputs, marked LO and HI. As the names suggest a low on the LO input will operate the relay. Similarly a high on the HI input will also operate the relay.

Specifications:
Operating Voltage 12VDC (or 24VDC)
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V (or 24VDC)

We have operated these relays from an old style TTL 7404 Hex Inverter which have less drive capacity than the newer HC and HCT types. The inverter could operate the relay with both a low and a high output signal. But what is more important was that the High voltage dropped from 4V to 3.5V showing the output still had capacity to drive other TTL devices

The relays used are Goodsky RW-SS-122D
Each single pole changeover relay contacts SPDT will switch 10A/24VDC , 10A/110VAC, 5A/240VAC.
Coil Resistance for the relays is 400ohm(12V), 1600ohm(24V)
Current consumption for 2 relay card (12V)
 All relays off 4mA
 One relay on 37mA
 Two relays on 70mA
Current consumption for 2 relay card (24V)
 All relays off 4mA
 One relay on 24mA
 Two relays on 44mA

A LED shows the state of each relay.
The Relay Cards are available in 12VDC or 24VDC
Four 3.5mm  holes in each corner allow easy mounting on a panel

Dimensions of card
2 relay card - 42(L) x 71(W) x 20(H)mm
4 relay card - 86(L) x 71(W) x 20(H)mm
6 relay card - 130(L) x 71(W) x 20(H)mm
8 relay card - 174(L) x 71(W) x 20(H)mm

Download Manual

Purchase!


2,4,6 or 8 Relay Cards DIN Rail Mounted
Our new multiple Relay Cards can be inserted into DIN rail mounts. This allows you to clip them to Top Hat or G style DIN rails. These cards have the same switching and load specifications (see above). They also feature LEDs to indicate the state of the relay.   They are available in 2, 4 and 8 Relays

Dimensions are
2 relay card - 46(L) x 77(W) x 41(H)mm
4 relay card - 90(L) x 77(W) x 41(H)mm
6 relay card - 134(L) x 77(W) x 41(H)mm
8 relay card - 178(L) x 77(W) x 41(H)mm



Purchase!


 

D25 Terminal Board!.........AUD$45.00
Our D25 male connector to screw connectors allows you to easily connect to I/O through a D25 connector. The board can be mounted using screws and spacers or purchased with DIN rail mounting as shown in the picture.

Purchase!

D25_terminal.jpg (5208 bytes)

All prices are in Australian Dollars. Prices do not include GST (Goods and Services Tax). 10% GST applies to goods delivered in Australia. Australian GST is not paid on shipments despatched to an international destination. You can check the exchange rate by going to http://www.x-rates.com

Item Description Quantity Price(AUD$)
RLC-122 Two 12VDC Relay Card $21.50
RLC-124 Four 12VDC Relay Card $42.50
RLC-128 Eight 12VDC Relay Card $85.00
RLD-122 Two 12VDC Relay Card on DIN Rail $40.00
RLD-124 Four 12VDC Relay Card on DIN Rail $75.00
RLD-128 Eight 12VDC Relay Card on DIN Rail $150.00
RLC-242 Two 24VDC Relay Card $21.50
RLC-244 Four 24VDC Relay Card $42.50
RLC-248 Eight 24VDC Relay Card $85.00
RLD-242 Two 24VDC Relay Card on DIN Rail $40.00
RLD-244 Four 24VDC Relay Card on DIN Rail $75.00
RLD-248 Eight 24VDC Relay Card on DIN Rail $150.00
DTC-025 D25 Terminal Board $45.00
DTD-025 D25 Terminal Board Mounter on DIN Rail $65.00



View Your Shopping Cart